TensorNodeStart free trial

FEA Tool manual › Chapter 5

Materials

Chapters
  1. 1 Getting started
  2. 2 The interface
  3. 3 Coordinate systems and conventions
  4. 4 Modelling
  5. 5 Materials
  6. 6 Sections
  7. 7 Supports, releases and modifiers
  8. 8 Loads
  9. 9 Load combinations
  10. 10 Meshing
  11. 11 Static analysis
  12. 12 Dynamic and seismic analysis
  13. 13 Results
  14. 14 Design
  15. 15 Scripting and the AI model builder
  16. 16 Import and export
  17. 17 Verification
  18. 18 Scope and limits
  19. 19 Troubleshooting
  20. 20 Glossary and notation
On this page
  1. 5.1 Material types and properties
  2. 5.2 The material library
  3. 5.3 Your own materials
  4. 5.4 Defaults and missing values
  5. 5.5 Nonlinear stress-strain curves
  6. 5.6 Hysteresis rules

A material gives the analysis its elastic constants, density and thermal expansion, and gives the design and the nonlinear analyses its strengths and stress-strain curve. Materials are picked from a library arranged by code region, or defined with your own values. This chapter lists the library, the properties each analysis reads, the default values the engine uses when a property is missing, and the nonlinear stress-strain laws with their hysteresis rules.

5.1 Material types and properties

Every material has a type: concrete, structural steel, reinforcing bar, prestressing tendon, aluminium, timber or other (your own values). The properties are:

PropertySymbolUnitRead by
modulus of elasticityEEMPaevery analysis
shear modulusGGMPaevery analysis; G=E/(2(1+ν))G = E/(2(1+\nu)) when only ν\nu is given
Poisson's ratioν\nuareas, and GG when GG is not given
densityρ\rhokg/m³self weight and mass
thermal expansion coefficientα\alpha1/°Ctemperature loads
yield and tensile strengthfyf_y, fuf_uMPadesign, plastic hinges, fibre sections
concrete compressive strengthfc′f'_c (fckf_{ck})MPadesign, fibre sections
timber strengthsfbf_b, ftf_t, fc0f_{c0}, fvf_vMPadesign
nonlinear curve and hysteresisfibre hinges of nonlinear and pushover analyses

The linear analyses (linear static, P-Delta, buckling, modal, response spectrum, linear time history) read only EE, GG, ρ\rho and α\alpha. Strengths matter to the design, to the plastic hinges of the nonlinear analyses and to the section designer.

5.2 The material library

Model > Materials shows the library of the code region in use. Pick an entry and press Assign material to give it to the selected members, or add it to the model for later use. Each entry holds the nominal or characteristic values of the product standard it names, with EE, GG, ν\nu, ρ\rho and α\alpha.

Table 5.1 Material library by region
TypeAS/NZUSCAEU
ConcreteN20 to N100 (AS 3600)3,000 to 10,000 psi (ACI 318)25 to 80 MPa (CSA A23.3)C12/15 to C90/105 (EN 1992-1-1)
Structural steelAS/NZS 3679.1 grades 250, 300, 350; AS/NZS 3678 plate; AS/NZS 1163 C250L0, C350L0, C450L0ASTM A36, A992, A572 Gr 50, A500 Gr B and CCSA G40.21 300W, 350WEN 10025 S235 to S460
Reinforcing barD500N, D500L, D250NA615 and A706 Gr 60400W, 500WB500B, B500C
Prestressing strand1750 and 1860 MPa1750 and 1860 MPa1750 and 1860 MPa1750 and 1860 MPa
Aluminium6061-T6, 6063-T6, 6082-T6, 5083-H116samesamesame
TimberMGP10, MGP12, MGP15, F8 to F27, GL10 to GL18NDS Douglas Fir-Larch No.1 and No.2, SPFCSA O86 SPF, D.Fir-LEN 338 C16, C24; EN 14080 GL24h to GL32h

For AS 3600 concrete, EE is the mean value of EcjE_{cj} at 28 days from AS 3600-2018 Table 3.1.2, ν=0.2\nu = 0.2, α=10×10−6\alpha = 10\times10^{-6}/°C and ρ=2400\rho = 2400 kg/m³.

Some library values are customary rather than taken from the standard (for example ν\nu and α\alpha of some concretes). Such a value is kept in the entry for reference only: the design uses the module's own default or the value you enter until you confirm it, and the material form marks which values those are.

5.3 Your own materials

Model > Materials > user values defines a material by type and properties. The form shows the shear modulus from EE and ν\nu and the density as a unit weight. In a script, tn.add_material(name, type, E, nu, rho, fy, fu, fc, alpha) does the same (Chapter 15).

5.4 Defaults and missing values

When a member names a material that is not in the model, the engine uses the defaults of the material type and says so in the messages of the run:

TypeEE (MPa)ρ\rho (kg/m³)α\alpha (1/°C)
steel200,00078501.2×10−51.2\times10^{-5}
concrete5050fc′5050\sqrt{f'_c}24501.0×10−51.0\times10^{-5}
timber10,0006005×10−65\times10^{-6}
aluminium(library)(library)2.3×10−52.3\times10^{-5}
other(given)(given)1.2×10−51.2\times10^{-5}

Density can also be given as density in kg/m³ or as a unit weight gamma in kN/m³; the engine reads either when ρ\rho is absent.

5.5 Nonlinear stress-strain curves

Nonlinear material data in the material form chooses a stress-strain curve and plots it as you edit the values. The curve is used by the fibre sections of the section designer and by fibre hinges in the nonlinear static and pushover analyses (Section 11.6). Concrete curves are written with compression positive, metal curves with tension positive.

Concrete: Mander

The Mander, Priestley and Park (1988) curve is the default for concrete. With x=εc/εccx = \varepsilon_c/\varepsilon_{cc},

fc=fcc′ x rr−1+xr,r=EcEc−Esec,Esec=fcc′εcc(5.1)f_c = \frac{f'_{cc}\, x\, r}{r - 1 + x^r}, \qquad r = \frac{E_c}{E_c - E_{\text{sec}}}, \qquad E_{\text{sec}} = \frac{f'_{cc}}{\varepsilon_{cc}} \tag{5.1}

For unconfined concrete fcc′=fco′f'_{cc} = f'_{co} and εcc=εco\varepsilon_{cc} = \varepsilon_{co} (default 0.002). For concrete confined by an effective lateral stress fl′f'_l,

fcc′=fco′(−1.254+2.2541+7.94fl′fco′−2fl′fco′),εcc=εco[1+5(fcc′fco′−1)](5.2)f'_{cc} = f'_{co}\left(-1.254 + 2.254\sqrt{1 + \frac{7.94 f'_l}{f'_{co}}} - \frac{2 f'_l}{f'_{co}}\right), \qquad \varepsilon_{cc} = \varepsilon_{co}\left[1 + 5\left(\frac{f'_{cc}}{f'_{co}} - 1\right)\right] \tag{5.2}

The ultimate strain defaults to 0.005 unconfined and 0.015 confined. Beyond 2εcc2\varepsilon_{cc} an unconfined cover falls linearly to zero at the spalling strain. In tension the concrete is linear up to ft=0.6fc′f_t = 0.6\sqrt{f'_c} and carries nothing after cracking.

Concrete: parabola-rectangle

The curve of EN 1992-1-1 3.1.7:

σc=fc[1−(1−εcεc2)n] for 0≤εc≤εc2,σc=fc for εc2<εc≤εcu2(5.3)\sigma_c = f_c\left[1 - \left(1 - \frac{\varepsilon_c}{\varepsilon_{c2}}\right)^{n}\right] \ \text{for}\ 0 \le \varepsilon_c \le \varepsilon_{c2}, \qquad \sigma_c = f_c \ \text{for}\ \varepsilon_{c2} < \varepsilon_c \le \varepsilon_{cu2} \tag{5.3}

with nn, εc2\varepsilon_{c2} and εcu2\varepsilon_{cu2} from EN 1992-1-1 Table 3.1 for the strength class.

Concrete: Hognestad and simple

The Hognestad curve is a parabola up to ε0\varepsilon_0 followed by a straight fall of 15 % of the peak at εu\varepsilon_u:

fc=fc′[2εcε0−(εcε0)2] for εc≤ε0,fc=fc′[1−0.15 εc−ε0εu−ε0] for ε0<εc≤εu(5.4)f_c = f'_c\left[\frac{2\varepsilon_c}{\varepsilon_0} - \left(\frac{\varepsilon_c}{\varepsilon_0}\right)^2\right] \ \text{for}\ \varepsilon_c \le \varepsilon_0, \qquad f_c = f'_c\left[1 - 0.15\,\frac{\varepsilon_c - \varepsilon_0}{\varepsilon_u - \varepsilon_0}\right] \ \text{for}\ \varepsilon_0 < \varepsilon_c \le \varepsilon_u \tag{5.4}

The simple curve has the same parabola, then a straight line whose slope is a chosen fraction of EE (the final slope) up to εu\varepsilon_u.

Metals: simple and Park

The simple metal curve is elastic to εy=fy/E\varepsilon_y = f_y/E, flat to the start of strain hardening εsh\varepsilon_{sh}, rises on a parabola to fuf_u at εsu\varepsilon_{su} and falls in a straight line to zero at the rupture strain εr\varepsilon_r:

fs=fu−(fu−fy)(εsu−εsεsu−εsh)2for εsh<εs≤εsu(5.5)f_s = f_u - (f_u - f_y)\left(\frac{\varepsilon_{su} - \varepsilon_s}{\varepsilon_{su} - \varepsilon_{sh}}\right)^2 \quad \text{for}\ \varepsilon_{sh} < \varepsilon_s \le \varepsilon_{su} \tag{5.5}

The Park curve (Park and Paulay 1975) is the usual choice for reinforcing bars. With r=εsu−εshr = \varepsilon_{su} - \varepsilon_{sh} and d=εs−εshd = \varepsilon_s - \varepsilon_{sh},

fs=fy[md+260d+2+d (60−m)2(30r+1)2],m=(fu/fy)(30r+1)2−60r−115r2(5.6)f_s = f_y\left[\frac{m d + 2}{60 d + 2} + \frac{d\,(60 - m)}{2(30r + 1)^2}\right], \qquad m = \frac{(f_u/f_y)(30r+1)^2 - 60r - 1}{15 r^2} \tag{5.6}

Defaults: εsh=0.01\varepsilon_{sh} = 0.01 for bars and 0.02 for structural steel; εr=1.6 εsu\varepsilon_r = 1.6\,\varepsilon_{su}.

User points

Any material can take a curve of your own as pairs of strain and stress. The first segment sets the initial modulus and the last point the ultimate strain.

How the fibres use the metal curves

In the fibre sections, a metal follows a bilinear law from (εy,fy)(\varepsilon_y, f_y) to (εsu,fu)(\varepsilon_{su}, f_u) with hardening ratio

b=fu−fyE(εsu−εy),10−4≤b≤0.2(5.7)b = \frac{f_u - f_y}{E(\varepsilon_{su} - \varepsilon_y)}, \qquad 10^{-4} \le b \le 0.2 \tag{5.7}

Concrete fibres use the concrete curve as given; a confined Mander curve is used for the core of a confined section.

5.6 Hysteresis rules

The hysteresis rule decides how a fibre unloads and reloads when the strain reverses. It matters in the pushover and nonlinear analyses where hinges unload, and in cyclic studies of a section.

RuleForBehaviour
Kinematic (default for metals)metalsthe elastic range keeps its size and moves with the stress
Isotropicmetalsthe elastic range grows with the plastic strain
BRBmetalshalf kinematic and half isotropic hardening, for buckling-restrained braces
Takedametalsunloading at EE, reloading on a line towards the largest earlier strain of that direction on the curve
Pivotmetalsunloading towards the pivot point (−αεy,−αfy)(-\alpha\varepsilon_y, -\alpha f_y) of the other side, reloading through (βεy,βfy)(\beta\varepsilon_y, \beta f_y); defaults α=2\alpha = 2, β=0.35\beta = 0.35
Degradingmetalsstress σ=f σkin+(1−f) σel\sigma = f\,\sigma_{\text{kin}} + (1-f)\,\sigma_{\text{el}} with ff falling from f0f_0 to f1f_1 and f2f_2 at x1x_1 and x2x_2 times εy\varepsilon_y
Concrete (default for concrete)concreteunloading and reloading on a straight line to the plastic strain of Karsan and Jirsa (1969), never steeper than EcE_c; tension linear to frf_r, then nothing
Elasticanyloading and unloading on the same curve, no energy dissipated

The plastic strain of the concrete rule after a largest compressive strain εmin⁡\varepsilon_{\min} is

εpεco=0.145(εmin⁡εco)2+0.13 εmin⁡εco(5.8)\frac{\varepsilon_p}{\varepsilon_{co}} = 0.145\left(\frac{\varepsilon_{\min}}{\varepsilon_{co}}\right)^2 + 0.13\,\frac{\varepsilon_{\min}}{\varepsilon_{co}} \tag{5.8}

For the degrading rule the defaults are f0=1f_0 = 1, f1=0.75f_1 = 0.75 and f2=0.5f_2 = 0.5 at x1=4x_1 = 4 and x2=10x_2 = 10, with 1≥f0≥f1≥f2>01 \ge f_0 \ge f_1 \ge f_2 > 0. Each loop then dissipates ff times the energy of the kinematic loop; f=1f = 1 throughout is the kinematic rule.

The lumped plastic hinges (PMM, PM and M, Section 11.6) and the hinges of the nonlinear time history keep their own elastic-perfectly-plastic rule and do not read these settings. The material form says in plain words which analyses a choice affects.