TensorNodeStart free trial

FEA Tool manual › Chapter 20

Glossary and notation

Chapters
  1. 1 Getting started
  2. 2 The interface
  3. 3 Coordinate systems and conventions
  4. 4 Modelling
  5. 5 Materials
  6. 6 Sections
  7. 7 Supports, releases and modifiers
  8. 8 Loads
  9. 9 Load combinations
  10. 10 Meshing
  11. 11 Static analysis
  12. 12 Dynamic and seismic analysis
  13. 13 Results
  14. 14 Design
  15. 15 Scripting and the AI model builder
  16. 16 Import and export
  17. 17 Verification
  18. 18 Scope and limits
  19. 19 Troubleshooting
  20. 20 Glossary and notation
On this page
  1. 20.1 Terms
  2. 20.2 Notation

This chapter defines the terms used in the FEA Tool and in this manual, and lists the symbols of the equations with their units.

20.1 Terms

Analysis model
The model as the engine solves it: members cut by the frame mesh and at intermediate joints, areas divided into elements, and the master joints of rigid diaphragms. Shown with Options > Show the analysis model.
Area
A surface object between three or more nodes, analysed as a shell, plate or membrane after meshing.
Area section
The named type, material and thicknesses of an area: shell-thin, shell-thick, plate-thin, plate-thick or membrane.
Auto-select list
A named list of sections; a member given the list is analysed with the median section by weight and designed to the lightest section that passes.
Buckling factor
The factor λ\lambda by which a base loading must be multiplied for the structure to buckle elastically.
Combination
A factored sum of load patterns, of kind strength or service.
Co-rotational
A formulation that follows each element through large rotations, used for geometric nonlinearity in the nonlinear static analysis.
CQC
Complete quadratic combination of modal responses, which allows for the correlation of closely spaced modes.
Degree of freedom (DOF)
One of the six displacements and rotations of a node: uxu_x, uyu_y, uzu_z, rxr_x, ryr_y, rzr_z.
Design module
A TensorNode calculation for one kind of member or check (for example Steel Member or Column Interaction), to which the FEA Tool sends each member with its design actions.
Diaphragm
A floor idealised as rigid in its plane; its joints follow a master joint at the centre of mass in uxu_x, uyu_y and rzr_z.
Drilling rotation
The rotation of a shell node about the normal to the shell, held by a penalty stiffness.
Envelope
The largest and smallest value of each result over a set of combinations, each taken independently.
Equivalent lateral force (ELF)
The static seismic method of a code, with a base shear from the design spectrum at the fundamental period distributed over the height.
Fibre hinge
A plastic hinge whose response is integrated over fibres of the section's own materials.
Frame-edge matching
Cutting frame members at the mesh nodes of areas that lie on them, so beams and slabs share nodes.
Frame member
A line object between two nodes, analysed as a frame, truss or cable element.
Joint pattern
A linear function p=Ax+By+Cz+Dp = Ax + By + Cz + D that describes a varying pressure on areas.
Level
A group of joints at one elevation, used for diaphragms, storey results and seismic forces.
Load pattern (load case)
One independent action, such as dead load or wind from one direction, with a type used by the combination generator.
Local axes
The axes 1, 2, 3 of a member or area in which its forces and loads are given.
Mass source
The definition of the mass used by the dynamic analyses: self mass, mass from load patterns, node masses.
Mesh
The division of members and areas into the finite elements the engine solves.
Modal participation
The share of the total mass of a direction that a mode carries.
P-Delta
The second-order effect of axial loads acting through lateral displacements.
Performance point
The target displacement of a pushover analysis found by the coefficient method of ASCE 41-17.
Plastic hinge
A point at a member end (or midspan) where yielding is concentrated in a nonlinear analysis.
Property modifier
A factor on a section property (stiffness, mass or weight) of a member or area.
Pushover
A nonlinear static analysis in which a lateral load pattern is increased until a control node reaches a target displacement.
Release
A member end force that is set to zero (a hinge or slider at the member end).
Rigid end offset
A length at a member end treated as rigid, for the depth of a joint.
Ritz vectors
Load-dependent basis vectors used instead of eigenvectors in the dynamic analyses.
Roll angle
The angle β\beta that turns a member's local axes 2 and 3 about axis 1.
Station
A point along a member at which internal forces and deflections are reported.
Sturm sequence check
A count of the eigenvalues below a shift, which proves that no mode or buckling factor below it was missed.
Utilisation
The ratio of the design action effect to the design capacity of the governing check; 1.00 is the limit.
Wood-Armer moments
Design moments that combine the bending and twisting moments of a slab into moments for an orthogonal reinforcement mesh.

20.2 Notation

Table 20.1 Symbols used in this manual
SymbolMeaningUnit
AAcross-section aream²
As2A_{s2}, As3A_{s3}shear areas along local 2 and 3m²
AsA_sreinforcement area per unit widthmm²/m
a0a_0, a1a_1Rayleigh damping coefficients1/s, s
CsC_s, CdC_dseismic response coefficient (ASCE 7), design action coefficient (AS 1170.4)
C0C_0, C1C_1, C2C_2coefficients of the ASCE 41-17 target displacement
C\mathbf{C}damping matrix; membrane constitutive matrix of a shell
D\mathbf{D}bending constitutive matrix of a shell
ddeffective depth of reinforcementmm
EE, GGmodulus of elasticity, shear modulusMPa
eeeccentricitym
F\mathbf{F}vector of nodal loadskN, kNm
F11F_{11}, F22F_{22}, F12F_{12}membrane forces of an areakN/m
fc′f'_c, fyf_y, fuf_uconcrete strength, yield and tensile strength of steelMPa
ggacceleration due to gravity, 9.81m/s²
g2g_2, g3g_3temperature gradients across a member°C/m
I22I_{22}, I33I_{33}second moments of area about local 2 and 3m⁴
JJtorsion constantm⁴
K\mathbf{K}, KG\mathbf{K}_G, KT\mathbf{K}_Telastic, geometric and tangent stiffness matrices
knk_n, k1k_1, k2k_2area spring modulikN/m³
LL, LeL_e, LbL_bmember length, effective length, unbraced lengthm
M\mathbf{M}mass matrixt
M2M_2, M3M_3member moments about local 2 and 3kNm
M11M_{11}, M22M_{22}, M12M_{12}bending and twisting moments of an areakNm/m
M∗M^{*}design momentkNm, kNm/m
NN, PPaxial force, positive in tensionkN
pppressure on an areakN/m²
qqarea load; behaviour factor (EN 1998-1)kN/m² (load)
RR, IeI_eresponse modification and importance factors (ASCE 7)
SaS_a, SdS_dspectral acceleration, design spectral accelerationg
TTperiod; torsion in a members (period), kNm (torsion)
tt, tmt_m, tbt_bthickness; membrane and bending thickness of an aream
u\mathbf{u}vector of nodal displacementsm, rad
uxu_x, uyu_y, uzu_z, rxr_x, ryr_y, rzr_znodal displacements and rotationsm, rad
VVbase shearkN
V2V_2, V3V_3member shear forces along local 2 and 3kN
V13V_{13}, V23V_{23}transverse shear forces of an areakN/m
WWseismic weightkN
α\alphacoefficient of thermal expansion; HHT parameter1/°C (thermal)
β\betaroll angle; Newmark parameter; frequency ratio in CQC° (roll angle)
γ\gammaunit weight; Newmark parameter; partial factorkN/m³ (unit weight)
Γn\Gamma_nparticipation factor of mode nn
ΔT\Delta Ttemperature change°C
δt\delta_ttarget displacement of a pushoverm
ε\varepsilon, σ\sigmastrain, stressMPa (stress)
κ\kappacurvature; shear correction factor1/m
λ\lambdaload factor; buckling factor
μ\mustructural ductility factor (AS 1170.4)
ν\nuPoisson's ratio
ρ\rhodensitykg/m³
ϕn\boldsymbol{\phi}_nmode shape or buckled shape nn
Φ\Phishear deformation parameter of the frame element
ψ\psicombination factors (ψc\psi_c, ψl\psi_l, ψs\psi_s, ψE\psi_E, ψ0\psi_0, ψ1\psi_1, ψ2\psi_2); end moment ratio
ωn\omega_ncircular frequency of mode nnrad/s
ζ\zetadamping ratio