Products and modules
Every design module in TensorNode, with the standards and editions it supports in each code system. Filter by material or code region, search, sort, and switch between cards and a table.
96 modules
Analysis
AnalysisGeneral single-span beam analysis: reactions, maximum bending moment and shear, and elastic deflection for a uniform and/or point load on a simply-supported, cantilever, propped-cantilever or fixed-end beam.
Anchor Bolt
Steel connectionsFastening to concrete (cast-in or post-installed anchor group) to AS 5216: tension by steel and concrete cone breakout, shear by steel and concrete edge breakout, and the combined tension-plus-shear interaction, with edge-distance and spacing effects.
- AS/NZ AS 5216:2021
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-4:2018
Base Plate
Steel connectionsSteel column base plate to AS 3600 §12.6 and AS 4100: concrete bearing with confinement √(A2/A1), plate flexure (thickness), and holding-down bolts in shear and (under uplift) tension, using a rectangular bearing stress-block at any eccentricity.
- AS/NZ AS 3600:2018, AS 4100:2020
- US AISC DG 1 (2nd ed.), ANSI/AISC 360-22
- CA CSA S16-19, CSA A23.3-19
- EU EN 1993-1-8:2005, EN 1992-1-1:2004+A1:2014
Basement Wall
Retaining walls and slabsBasement wall: RC wall panel embedded within a structure (basement), propped at top (floor slab/beam) and base (footing).
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014, EN 1997-1:2004+A1:2013
Beam Shear
ConcreteReinforced-concrete beam shear to AS 3600 §8.2: concrete contribution φVuc plus shear-reinforcement φVus (vertical stirrups), with the minimum-reinforcement and maximum-spacing detailing and the web-crushing limit.
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Beam Torsion
ConcreteReinforced-concrete beam torsion to AS 3600:2018 Cl.
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Beam-Column
Steel membersSteel member under combined axial compression and bending to AS 4100 §8: compression member capacity, in-plane and out-of-plane member moment checks (N + Mx), and the biaxial contour where a minor-axis moment is present.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005
Bolt Group
Steel membersBolt group under shear plus an out-of-plane moment to AS 4100 §9: the shear is shared equally while the moment is resisted by tension that grows linearly from the group centroid; the top (extreme) bolt and the combined shear-tension interaction govern.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-8:2005
Bolt Tension
Steel membersBolt in tension with prying to AS 4100 §9: a T-stub model adds the prying force from the flexible connected plate to the applied tension; the bolt is checked for the total and the plate thickness for prying control.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-8:2005
Bolts
Steel connectionsSingle high-strength bolt capacity to AS 4100 §9.3: shear (threads in/out of the shear plane, single/double shear), ply bearing and tear-out, tension, and the combined shear-and-tension interaction.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-8:2005
Bondbeam
MasonryReinforced masonry bond beam / lintel to AS 3700: the span moment and shear from the applied load, the reinforced flexural capacity, the masonry shear capacity and the minimum reinforcement.
- AS/NZ AS 3700:2018
- US TMS 402-22
- CA CSA S304-14
- EU EN 1996-1-1:2005+A1:2012
Bored Pier
FootingsBored (CFA/cast-in-situ) pier: drilled hole, concrete cast in-situ.
- AS/NZ AS 2159:2009
- US IBC 2018, ACI CODE-318-25
- CA NBC 2020, CSA A23.3-19
- EU EN 1997-1:2004+A1:2013, EN 1992-1-1:2004+A1:2014, EN 1990:2002+A1:2005
Circular Column
TimberCircular timber column / pole to AS 1720.1 §3.3: axial compression with the slenderness stability factor k12 on the round section, plus optional bending (no lateral-torsional buckling for a circular section).
- AS/NZ AS 1720.1:2010
- US ANSI/AWC NDS-2018
- CA CSA O86-19
- EU EN 1995-1-1:2004+A2:2014, EN 1990:2002+A1:2005
Cleat Plate
Steel connectionsFin/cleat shear connection to AS 4100 §9: the eccentric bolt group (direct shear + torsion from the eccentricity), bolt bearing on the cleat, the cleat in shear yield and net-section rupture, and the support weld for V plus the eccentric moment.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-8:2005
Column Biaxial
ConcreteRC column under axial load with biaxial bending to AS 3600 §10.6.3, the P-M interaction is built by strain compatibility about each axis, with reinforcement placed on all four faces (top/bottom bars resist X-axis bending, side bars resist Y-axis bending, both
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Column Interaction
ConcreteRectangular reinforced-concrete column to AS 3600 §10: squash load, full N-M interaction by strain compatibility, biaxial bending about both axes, capacity-point table and slenderness screen.
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Combined Footing
FootingsCombined footing supporting two columns: the uniform bearing pressure, the longitudinal beam moments (hogging at the columns, sagging between), the transverse cantilever moment and the one-way shear, with reinforcement.
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1997-1:2004+A1:2013, EN 1992-1-1:2004+A1:2014, EN 1990:2002+A1:2005
Composite Member
CompositeSimply-supported composite steel-and-concrete beam to AS 2327: a library steel section acting compositely with a profiled-deck slab (Bondek / Condek / KingFlor / RF / solid), with the effective flange width, the plastic composite moment capacity, the degree of
- AS/NZ AS 2327:2017
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1994-1-1:2004, EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005
Compression Strut
Steel membersAxially-loaded steel member (strut / column) to AS 4100: section and member compression capacity with the §6.3.3 slenderness reduction, plus minor-axis and combined (biaxial) bending.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005
Concrete Durability and Cover
ConcreteDurability and cover to reinforcement to AS 3600:2018 Section 4: exposure classification (Table 4.3, with the sulfate and saline soil tables 4.8.1 and 4.8.2), minimum f'c and curing (Table 4.4, with the abrasion and freezing and thawing limits of Table 4.6 and
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.1-19
- EU EN 1992-1-1:2004+A1:2014
Concrete Wall
ConcreteRC wall in compression by the AS 3600 §11.5.3 simplified method: the design axial capacity per metre from the wall thickness, the load eccentricity and the slenderness-derived additional eccentricity, with the minimum vertical reinforcement.
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Corbel / Bracket
ConcreteReinforced-concrete corbel / bracket to AS 3600: shear-friction with the casting-interface condition (monolithic / roughened / smooth / against steel), main tension tie and closed ties from the vertical and horizontal actions, bearing and the maximum shear lim
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Crack Control
ConcreteCrack control for RC beams/slabs by the AS 3600 §8.6.2.2 deemed-to-comply method: the serviceability steel stress is checked against the larger of the bar-diameter and bar-spacing limits (Tables 8.6.2.2(A) and (B), selected w'max), plus the minimum tensile rei
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Crane Beam
Steel membersOverhead-crane runway beam: moving wheel loads positioned for the absolute-maximum moment and reaction (with impact), lateral surge on the top flange, and AS 4100 bending/shear/combined capacity.
- AS/NZ AS 4100:2020, AS 1418.18
- US ANSI/AISC 360-22, AISC DG 7, ASCE/SEI 7-22
- CA CSA S16-19, NBC 2020
- EU EN 1993-1-1:2005+A1:2014, EN 1993-6:2007, EN 1991-3:2006, EN 1993-1-9:2005
Dead & Live Loads
AnalysisLoad takedown: builds the permanent (G) action from its components and the imposed (Q) action, applies the AS/NZS 1170.0 ULS and SLS combinations, and converts to a design line load over a tributary width.
- AS/NZ AS/NZS 1170.1:2002
- US ASCE/SEI 7-22
- CA NBC 2020
- EU EN 1990:2002+A1:2005
Deep Beam
ConcreteRC deep beam (span/depth < 2) by strut-and-tie to AS 3600 §7: a diagonal concrete strut carries the load to the supports and a bottom tie carries the tension; the strut, tie, node bearing and diagonal-compression limit are checked.
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Development & Laps
ConcreteReinforcement development and lap lengths to AS 3600 §13: basic tension development length Lsy.tb (with the bar-position, cover/confinement and concrete-strength factors), compression development, and tension/compression lap lengths.
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Drainage
DrainagePipe / drain capacity by the Manning equation: the full-bore velocity and flow capacity for a circular pipe at a given grade and roughness, with a self-cleansing-velocity check and an optional capacity-versus-demand check.
- AS/NZ AS/NZS 3500.3
- US IPC 2018, ASCE/SEI 7-22
- CA NPC 2020, NBC 2020
- EU EN 12056-3, EN 752
Earth Pressure
Retaining walls and slabsLateral earth pressure by Rankine theory: active, at-rest or passive coefficient, the soil/surcharge/water pressure diagram, the total thrust and its line of action for use in retaining-wall and basement design.
- AS/NZ AS 4678:2002
- US ASCE/SEI 7-22
- CA NBC 2020
- EU EN 1997-1:2004+A1:2013
Earthquake Design Category
Earthquake actionsEarthquake Design Category (EDC) determination to AS 1170.4 §2: from the hazard product kp·Z, the site sub-soil class, the structure height and the importance level, giving the required analysis method.
- AS/NZ AS 1170.4:2007
- US ASCE/SEI 7-22
- CA NBC 2020
- EU EN 1998-1:2004+A1:2013
Eccentric Bolt Group
Steel membersBolt group under in-plane eccentric shear (a bracket) to AS 4100 §9: the elastic vector method combines the direct shear with the torsional shear from the eccentric moment; the critical corner bolt governs.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-8:2005
Eccentric Pad
FootingsEccentrically-loaded pad footing: biaxial bearing under N with moments Mx, My: the four corner pressures, the kern (no-uplift) check, and the flexural reinforcement.
- AS/NZ AS 3600:2018, AS 2159:2009
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1997-1:2004+A1:2013, EN 1992-1-1:2004+A1:2014, EN 1990:2002+A1:2005
End Plate
Steel connectionsBolted moment end-plate connection to AS 4100 §9: the flange tension force from the moment is resisted by the tension-bolt rows, the bolts are checked in shear, the end plate in yield-line flexure, and the tension-flange weld is sized for the flange force.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-8:2005
F17 Span Tables
TimberMaximum span for an F-grade timber member: the bending-limited span (φMb = wL²/8) and the deflection-limited span (δ = L/limit) for a chosen section, spacing and load; the lesser governs.
- AS/NZ AS 1720.1:2010
- US ANSI/AWC NDS-2018, IRC 2018
- CA CSA O86-19, NBC 2020
- EU EN 1995-1-1:2004+A2:2014, EN 1990:2002+A1:2005
FRP Flexural Strengthening
ConcreteExternally bonded FRP (carbon, glass or aramid; fabric or pre-cured laminate) on the soffit of an existing reinforced concrete beam or slab strip: ACI PRC-440.2-17 Chapter 10 with debonding, the initial strain at installation, the strengthening limit, service
- US ACI PRC-440.2-17, ACI CODE-318-19
Flag
Wind actionsWind drag on a flag/banner and pole base moment: flag mass, shape, height and length.
- AS/NZ AS/NZS 1170.2:2021
- US ASCE/SEI 7-22
- CA NBC 2020
- EU EN 1991-1-4:2005+A1:2010
Flat Slab
ConcreteFlat slab (column-supported, no beams) by the Direct Design Method: the total static moment per panel, its negative/positive split, the column-strip and middle-strip distribution in both directions, and the top and bottom reinforcement (bar diameter and spacin
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Flexure Member
ConcreteRectangular, T- and L-beam flexure to AS 3600: bar-by-bar reinforcement (number and size), with the section classified balanced / under- / over-reinforced, a tension-steel yielding check, minimum and maximum steel, optional compression steel (doubly-reinforced
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Floor Beam
Steel membersSimply-supported steel floor beam to AS 4100: factored UDL and midspan point load, section and member (lateral-torsional) moment, shear, and the floor deflection limits (live ≤ span/360, total ≤ span/250).
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005
Free Roof / Canopy
Wind actionsNet wind pressure and uplift on a free/canopy roof: canopy & average height, width, length, blocked underneath, enclosed sides and roof area.
- AS/NZ AS/NZS 1170.2:2021
- US ASCE/SEI 7-22
- CA NBC 2020
- EU EN 1991-1-4:2005+A1:2010
Hoarding
Wind actionsSolid hoarding / freestanding wall: drag force and base overturning moment per panel.
- AS/NZ AS/NZS 1170.2:2021
- US ASCE/SEI 7-22
- CA NBC 2020
- EU EN 1991-1-4:2005+A1:2010
Industrial Slab
Retaining walls and slabsIndustrial slab-on-grade under a concentrated (wheel/post) load: the radius of relative stiffness and the Westergaard interior and edge flexural stresses, checked against the allowable concrete flexural strength.
- AS/NZ AS 3600:2018
- US ACI 360R-10, ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014, Concrete Society TR34
Joint
TimberTimber joint (bolted / nailed / screwed) lateral capacity to AS 1720.1 §4: the design capacity from the characteristic fastener capacity, the number of fasteners and the modification factors, checked against the design action.
- AS/NZ AS 1720.1:2010
- US ANSI/AWC NDS-2018
- CA CSA O86-19
- EU EN 1995-1-1:2004+A2:2014
Load Stiffener
Steel membersLoad-bearing web stiffener to AS 4100 §5.14: a pair (or pairs) of stiffeners at a bearing/point load: the bearing-yield capacity and the buckling capacity of the stiffener-plus-web strut are checked against the applied reaction.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005, EN 1993-1-5:2006
Masonry Member
MasonryUnreinforced masonry wall/member in vertical compression to AS 3700: the characteristic compressive strength from the unit strength and mortar factor, the slenderness reduction, and the design compression capacity.
- AS/NZ AS 3700:2018
- US TMS 402-22
- CA CSA S304-14
- EU EN 1996-1-1:2005+A1:2012
Masonry Pier
MasonryMasonry pier in compression to AS 3700: the same §7.3 compression model applied to an isolated pier (engaged or freestanding) carrying a concentrated load, with the slenderness reduction.
- AS/NZ AS 3700:2018
- US TMS 402-22
- CA CSA S304-14
- EU EN 1996-1-1:2005+A1:2012
Monoslope Roof
Wind actionsWind pressures on a monoslope (skillion) roof to AS 1170.2 §5.4: the external pressure coefficients for the upwind/downwind slopes combined with the internal pressure give the net uplift and downward design pressures.
- AS/NZ AS/NZS 1170.2:2021
- US ASCE/SEI 7-22
- CA NBC 2020
- EU EN 1991-1-4:2005+A1:2010
Mullion
Steel membersSteel wall mullion / wind post to AS 4100: a vertical member spanning between floors under lateral wind pressure on its tributary width; checks bending, shear and the (governing) wind deflection.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005, EN 1991-1-4:2005+A1:2010
One-Way Slab
ConcreteOne-way reinforced-concrete slab to AS 3600: user-input bar diameter and spacing for the bottom (sag), top (hog) and secondary layers, with factored and service loads; flexure, one-way shear, service deflection, minimum reinforcement and crack-control checks.
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
PFC & Plate
Steel membersBuilt-up beam from a PFC (parallel-flange channel) with a welded plate: the combined section properties (about the composite neutral axis) and the section moment and shear capacities to AS 4100.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014, EN 1993-1-8:2005
Pad Foundation
FootingsFactored loading with eccentricity, uplift, sliding and overturning; two-way reinforcement by mesh (SL/RL) or bar diameter + spacing.
- AS/NZ AS 3600:2018, AS 2159:2009
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1997-1:2004+A1:2013, EN 1992-1-1:2004+A1:2014, EN 1990:2002+A1:2005
Piered Beam
FootingsReinforced-concrete ground beam spanning between bored piers: the wall/structure line load gives the span moment and shear; the RC section is checked for flexure, minimum steel, shear and deflection.
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1997-1:2004+A1:2013, EN 1992-1-1:2004+A1:2014, EN 1990:2002+A1:2005
Pins
Steel connectionsPin connection to AS 4100 §9.4: the pin in shear (one or more shear planes), bearing between the pin and the connected plies, and pin bending from the ply spacing.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-8:2005
Plain Concrete
ConcretePlain (unreinforced) concrete member to AS 3600 §20, a rectangular member of width b, depth D and bearing length L set by the user.
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Portal Frame
Steel membersSingle-bay portal frame to AS 4100: the gravity and wind load cases give the knee and apex moments; the rafter and column (as beam-columns) are checked against their member moment capacities at the critical knee.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005
Portal Knee
Steel connectionsBolted moment end-plate at a portal-frame knee: the rafter/column moment and shear are resisted by the tension-bolt group, the end-plate in bending and the welds; capacities are checked against the knee actions.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-8:2005, EN 1993-1-1:2005+A1:2014
Post Footing
FootingsEmbedded post footing driven by lateral load, applied moment, load height, footing width/depth and soil φ/γ (embedment depth governs).
- US IBC 2018
- CA NBC 2020
- EU EN 1997-1:2004+A1:2013
Propped Beam
Steel membersSteel propped cantilever to AS 4100: UDL with the fixed-end (hogging) and span (sagging) moments, the wall and prop reactions, the maximum shear at the fixed end, and the deflection limit.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005
Punching Shear
ConcreteTwo-way (punching) shear at a slab-column connection to AS 3600 §9.3: circular or rectangular column, interior/edge/corner case, unbalanced-moment transfer, and shear-reinforcement / integrity check.
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Purlin & Girt Loads
Wind actionsPurlin/girt member under wind to AS 4100: the wind line load over the member spacing gives the span moment, shear and deflection, checked against the section/member capacities (single or lapped/continuous).
- AS/NZ AS 4100:2020
- US ASCE/SEI 7-22, ANSI/AISC 360-22
- CA NBC 2020, CSA S16-19
- EU EN 1991-1-4:2005+A1:2010, EN 1993-1-1:2005+A1:2014
Rainfall Intensity (AEP)
DrainageDesign rainfall intensity expressed in the modern annual-exceedance-probability (AEP) frequency descriptor: converts the AEP to an equivalent ARI and returns the IFD intensity and optional peak flow.
- AS/NZ ARR 2019, AS/NZS 3500.3
- US NOAA Atlas 14, IPC 2018, ASCE/SEI 7-22
- CA NBC 2020, NPC 2020
- EU EN 12056-3, EN 752
Rainfall Intensity (ARI)
DrainageDesign rainfall intensity for a chosen average recurrence interval (ARI) and storm duration from the site IFD coefficients, with the equivalent AEP and an optional Rational-Method peak flow.
- AS/NZ AS/NZS 3500.3
- US NOAA Atlas 14, IPC 2018, ASCE/SEI 7-22
- CA NBC 2020, NPC 2020
- EU EN 12056-3, EN 752
Reinforcement Table
ConcreteReinforcement quantity reference: bar area, number of bars per metre and steel area for a chosen bar diameter and spacing (or count over a width), with a quick area-per-metre lookup grid.
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19, CSA G30.18
- EU EN 1992-1-1:2004+A1:2014, EN 10080
Residential Slab
Retaining walls and slabsStiffened-raft / waffle footing screening to AS 2870: for the site class and construction type it gives the deemed-to-comply stiffening-beam depth and maximum beam spacing (Table 3.1) and checks the provided raft against them.
- AS/NZ AS 2870:2011
- US IBC 2018, IRC 2018, ACI CODE-318-25
- CA NBC 2020, CSA A23.1-19, CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014, EN 1997-1:2004+A1:2013, EN 1990:2002+A1:2005
Retaining Wall
Retaining walls and slabsGeneric cantilever retaining wall: toe and heel, base thickness, optional shear key and drained/undrained (water table) condition; stem BMD/SFD, overturning, sliding (incl.
- AS/NZ AS 4678:2002, AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1997-1:2004+A1:2013, EN 1992-1-1:2004+A1:2014
Roof Beam
Steel membersSteel roof beam/rafter to AS 4100: gravity (1.2G + 1.5Q) and net wind-uplift (0.9G + Wu) load cases, section and member moment, shear, and the imposed/wind deflection limits.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005
Section Properties
AnalysisSection property calculator: looks up a hot-rolled library section (area, second moments, section/plastic moduli, radii of gyration, mass) or computes the properties of a custom rectangular, circular or I-shape from first principles.
- AS/NZ AS/NZS 3679.1
Shelf Angle
Steel membersShelf angle / masonry support angle to AS 4100: the eccentric brick load bends the angle leg; the leg bending capacity and the fixing-bolt shear back to the structure are checked per metre.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014, EN 1993-1-8:2005
Sleeper Wall
Retaining walls and slabsSleeper wall: steel posts embedded in soil, with timber or concrete sleeper planks spanning horizontally between posts.
- AS/NZ AS 4678:2002
- US IBC 2018, ANSI/AWC NDS-2018, ANSI/AISC 360-22
- CA NBC 2020, CSA O86-19, CSA S16-19
- EU EN 1997-1:2004+A1:2013, EN 1993-1-1:2005+A1:2014, EN 1995-1-1:2004+A2:2014
Snow Loads
Snow actionsRoof snow load s = s_g·C_e·μ_i to AS/NZS 1170.3:2003 for mono-pitched and duo-pitched roofs, obstructed roofs and lower roofs beside a step, with the ground snow load s_g from the snow region and the elevation (Section 5), the alpine or sub-alpine shape coeffi
- AS/NZ AS/NZS 1170.3:2003
- US ASCE/SEI 7-22
- CA NBC 2020
- EU EN 1991-1-3:2003+A1:2015
Stair
ConcreteRC stair flight (waist slab): the dead load of the inclined waist and steps plus the live load, the span moment and shear, the flexural reinforcement and the span/depth serviceability check.
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Static Analysis
Earthquake actionsEquivalent static earthquake analysis to AS 1170.4: the spectral shape factor, the horizontal design coefficient, the base shear and its vertical distribution up the height of a regular building.
- AS/NZ AS 1170.4:2007
- US ASCE/SEI 7-22
- CA NBC 2020
- EU EN 1998-1:2004+A1:2013
Steel Column
Steel membersAxially-loaded steel column to AS 4100 §6: section capacity (yield), member capacity (flexural buckling) with user-selected end fixity per axis (Le = ke·L), and the slenderness limit.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005
Steel Member
Steel membersHot-rolled steel member (UB / UC / PFC / TFB) to AS 4100: section moment, member lateral-torsional buckling, shear and section compression.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005
Steel Member in Fire
Fire designFire resistance of a steel beam or column to AS 4100:2020 Section 12: exposed surface area to mass ratio k_sm for three or four sided exposure, limiting temperature T_l = 905 - 690r_f, time to reach T_l for an unprotected member (Cl.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-2:2005
Stormwater Detention
DrainageOn-site stormwater detention (OSD): the pre- and post-development peak flows, the required detention storage volume and the orifice size to throttle the outflow to the permitted site-discharge.
- AS/NZ AS/NZS 3500
- EU EN 752
Strip Footing
FootingsContinuous strip footing under a wall line-load: bearing pressure, the cantilever face moment and reinforcement, and one-way shear, all per metre run.
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1997-1:2004+A1:2013, EN 1992-1-1:2004+A1:2014, EN 1990:2002+A1:2005
Strut & Tie
ConcreteStrut-and-tie model for a concrete D-region / deep beam to AS 3600 §7: strut efficiency factor βs, diagonal-strut and bottom-tie capacities, node bearing, the diagonal-compression limit, and tie reinforcement (bar diameter and number).
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Symbols
UtilitiesNotation and symbol reference: the common symbols used across the Australian Standards (general, actions, concrete, steel, timber, masonry, geotechnical) with their meaning and source standard.
T / Angle Lintel
Steel membersSteel lintel (angle, PFC or flat) over a masonry opening: masonry arching (triangular) load to AS 3700, bending and deflection to AS 4100, and support bearing.
- AS/NZ AS 4100:2020, AS 3700:2018
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014, EN 1996-1-1:2005+A1:2012
Taper Haunch
Steel connectionsTapered haunch at a portal-frame knee: the deepened (haunched) section at the knee and the rafter section at the haunch toe are checked for moment, with the lateral-torsional capacity of the unrestrained inner (compression) flange over the haunch length, plus
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014
Tension Member
Steel membersAxially-loaded steel tension member to AS 4100 §7.2: gross-section yield and net-section fracture, including the end-connection eccentricity factor kt and net-area (bolt-hole) reduction.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005, EN 1993-1-8:2005
Terrain Change
Wind actionsWind terrain/height multiplier with a terrain-category change to AS 1170.2 §4.2: the lag-distance interpolation between the upwind and downwind categories gives the governing M_z,cat, the design wind speed and the dynamic pressure.
- AS/NZ AS/NZS 1170.2:2021
- US ASCE/SEI 7-22
- CA NBC 2020
- EU EN 1991-1-4:2005+A1:2010
Timber Column
TimberTimber column/post to AS 1720.1 §3.3: axial compression with the slenderness stability factor k12 about both axes; the worse axis governs.
- AS/NZ AS 1720.1:2010
- US ANSI/AWC NDS-2018
- CA CSA O86-19
- EU EN 1995-1-1:2004+A2:2014, EN 1990:2002+A1:2005
Timber Floor Beam
TimberSawn/LVL timber floor beam to AS 1720.1: bending with lateral-stability k12, shear, and the creep-affected total deflection plus the live-load deflection.
- AS/NZ AS 1720.1:2010
- US ANSI/AWC NDS-2018
- CA CSA O86-19
- EU EN 1995-1-1:2004+A2:2014, EN 1990:2002+A1:2005
Timber Member
TimberSawn / glulam rectangular timber member to AS 1720.1: bending, shear, compression, tension and combined actions, with the k-factor capacity model and slenderness (k12) stability.
- AS/NZ AS 1720.1:2010
- US ANSI/AWC NDS-2018
- CA CSA O86-19
- EU EN 1995-1-1:2004+A2:2014, EN 1990:2002+A1:2005
Timber Member in Fire
Fire designFire resistance of a timber beam or column to AS 1720.4 by the residual section method: char rate from the timber density or Table 2.5.1, the 7.0 mm uncharred layer of Eq 2.6.1, residual section, and the bending, shear or compression capacity of the residual s
- AS/NZ AS 1720.4:2019
- US ANSI/AWC NDS-2018
- CA CSA O86-19
- EU EN 1995-1-2:2004
Timber Roof Beam
TimberTimber roof beam/rafter to AS 1720.1: gravity (G + Q) and wind (including net uplift) load cases, bending with k12, shear, and deflection.
- AS/NZ AS 1720.1:2010
- US ANSI/AWC NDS-2018
- CA CSA O86-19
- EU EN 1995-1-1:2004+A2:2014, EN 1990:2002+A1:2005
Tree Effects: Piers
FootingsBored pier through a tree-affected reactive (drying/swelling) zone: checks the uplift on the shaft from the reactive soil against the structure dead load plus the anchorage below the active zone, and the minimum embedment below that zone.
- AS/NZ AS 2870:2011, AS 2159:2009
Tree Effects: y_s
Retaining walls and slabsCharacteristic surface movement y_s and AS 2870 site classification, including the effect of nearby trees that dry the soil more deeply: the instability index, design suction change and depth of suction change give y_s, which trees increase by extending the ac
- AS/NZ AS 2870:2011
Two-Way Slab
ConcreteTwo-way spanning slab supported on four edges: the Grashof load share between the short and long spans, the positive span moments (and support hogging if continuous), reinforcement each way and the span/depth deflection control.
- AS/NZ AS 3600:2018
- US ACI CODE-318-25
- CA CSA A23.3-19
- EU EN 1992-1-1:2004+A1:2014
Unit Conversions
UtilitiesEngineering unit converter: enter a value in the SI base unit of a quantity (force, stress, moment, length, line load or area) and read it in all the common alternative units.
Web Bearing
Steel membersSteel web bearing under a concentrated load/reaction to AS 4100 §5.13: bearing yield and bearing buckling (web as a column), with the 1:2.5 flange dispersion and the interior/end stiff-bearing condition.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005, EN 1993-1-5:2006
Weld Group
Steel membersFillet weld group under in-plane eccentric shear to AS 4100 §9.7: the welds are treated as unit-throat line elements; the direct shear and the torsional shear from the eccentric moment are combined at the critical point and checked against the per-length capac
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-8:2005
Welds
Steel connectionsFillet weld capacity to AS 4100 §9.7.3: design throat from the leg size, the capacity per unit length for the electrode and weld category (SP/GP), and the check against the resultant design force per unit length.
- AS/NZ AS 4100:2020
- US ANSI/AISC 360-22
- CA CSA S16-19
- EU EN 1993-1-8:2005
Wind Actions
Wind actionsSite wind speed and design pressures with importance level, design life, roof pitch, average/roof height, blocked-underneath internal pressure and area-reduction Ka.
- AS/NZ AS/NZS 1170.2:2021
- US ASCE/SEI 7-22
- CA NBC 2020
- EU EN 1991-1-4:2005+A1:2010
| Module | Group | AS/NZ | US | CA | EU |
|---|---|---|---|---|---|
| Analysis | Analysis | - | - | - | - |
| Anchor Bolt | Steel connections | AS 5216:2021 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-4:2018 |
| Base Plate | Steel connections | AS 3600:2018, AS 4100:2020 | AISC DG 1 (2nd ed.), ANSI/AISC 360-22 | CSA S16-19, CSA A23.3-19 | EN 1993-1-8:2005, EN 1992-1-1:2004+A1:2014 |
| Basement Wall | Retaining walls and slabs | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014, EN 1997-1:2004+A1:2013 |
| Beam Shear | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Beam Torsion | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Beam-Column | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005 |
| Bolt Group | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-8:2005 |
| Bolt Tension | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-8:2005 |
| Bolts | Steel connections | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-8:2005 |
| Bondbeam | Masonry | AS 3700:2018 | TMS 402-22 | CSA S304-14 | EN 1996-1-1:2005+A1:2012 |
| Bored Pier | Footings | AS 2159:2009 | IBC 2018, ACI CODE-318-25 | NBC 2020, CSA A23.3-19 | EN 1997-1:2004+A1:2013, EN 1992-1-1:2004+A1:2014, EN 1990:2002+A1:2005 |
| Circular Column | Timber | AS 1720.1:2010 | ANSI/AWC NDS-2018 | CSA O86-19 | EN 1995-1-1:2004+A2:2014, EN 1990:2002+A1:2005 |
| Cleat Plate | Steel connections | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-8:2005 |
| Column Biaxial | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Column Interaction | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Combined Footing | Footings | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1997-1:2004+A1:2013, EN 1992-1-1:2004+A1:2014, EN 1990:2002+A1:2005 |
| Composite Member | Composite | AS 2327:2017 | ANSI/AISC 360-22 | CSA S16-19 | EN 1994-1-1:2004, EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005 |
| Compression Strut | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005 |
| Concrete Durability and Cover | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.1-19 | EN 1992-1-1:2004+A1:2014 |
| Concrete Wall | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Corbel / Bracket | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Crack Control | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Crane Beam | Steel members | AS 4100:2020, AS 1418.18 | ANSI/AISC 360-22, AISC DG 7, ASCE/SEI 7-22 | CSA S16-19, NBC 2020 | EN 1993-1-1:2005+A1:2014, EN 1993-6:2007, EN 1991-3:2006, EN 1993-1-9:2005 |
| Dead & Live Loads | Analysis | AS/NZS 1170.1:2002 | ASCE/SEI 7-22 | NBC 2020 | EN 1990:2002+A1:2005 |
| Deep Beam | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Development & Laps | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Drainage | Drainage | AS/NZS 3500.3 | IPC 2018, ASCE/SEI 7-22 | NPC 2020, NBC 2020 | EN 12056-3, EN 752 |
| Earth Pressure | Retaining walls and slabs | AS 4678:2002 | ASCE/SEI 7-22 | NBC 2020 | EN 1997-1:2004+A1:2013 |
| Earthquake Design Category | Earthquake actions | AS 1170.4:2007 | ASCE/SEI 7-22 | NBC 2020 | EN 1998-1:2004+A1:2013 |
| Eccentric Bolt Group | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-8:2005 |
| Eccentric Pad | Footings | AS 3600:2018, AS 2159:2009 | ACI CODE-318-25 | CSA A23.3-19 | EN 1997-1:2004+A1:2013, EN 1992-1-1:2004+A1:2014, EN 1990:2002+A1:2005 |
| End Plate | Steel connections | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-8:2005 |
| F17 Span Tables | Timber | AS 1720.1:2010 | ANSI/AWC NDS-2018, IRC 2018 | CSA O86-19, NBC 2020 | EN 1995-1-1:2004+A2:2014, EN 1990:2002+A1:2005 |
| FRP Flexural Strengthening | Concrete | - | ACI PRC-440.2-17, ACI CODE-318-19 | - | - |
| Flag | Wind actions | AS/NZS 1170.2:2021 | ASCE/SEI 7-22 | NBC 2020 | EN 1991-1-4:2005+A1:2010 |
| Flat Slab | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Flexure Member | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Floor Beam | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005 |
| Free Roof / Canopy | Wind actions | AS/NZS 1170.2:2021 | ASCE/SEI 7-22 | NBC 2020 | EN 1991-1-4:2005+A1:2010 |
| Hoarding | Wind actions | AS/NZS 1170.2:2021 | ASCE/SEI 7-22 | NBC 2020 | EN 1991-1-4:2005+A1:2010 |
| Industrial Slab | Retaining walls and slabs | AS 3600:2018 | ACI 360R-10, ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014, Concrete Society TR34 |
| Joint | Timber | AS 1720.1:2010 | ANSI/AWC NDS-2018 | CSA O86-19 | EN 1995-1-1:2004+A2:2014 |
| Load Stiffener | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005, EN 1993-1-5:2006 |
| Masonry Member | Masonry | AS 3700:2018 | TMS 402-22 | CSA S304-14 | EN 1996-1-1:2005+A1:2012 |
| Masonry Pier | Masonry | AS 3700:2018 | TMS 402-22 | CSA S304-14 | EN 1996-1-1:2005+A1:2012 |
| Monoslope Roof | Wind actions | AS/NZS 1170.2:2021 | ASCE/SEI 7-22 | NBC 2020 | EN 1991-1-4:2005+A1:2010 |
| Mullion | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005, EN 1991-1-4:2005+A1:2010 |
| One-Way Slab | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| PFC & Plate | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014, EN 1993-1-8:2005 |
| Pad Foundation | Footings | AS 3600:2018, AS 2159:2009 | ACI CODE-318-25 | CSA A23.3-19 | EN 1997-1:2004+A1:2013, EN 1992-1-1:2004+A1:2014, EN 1990:2002+A1:2005 |
| Piered Beam | Footings | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1997-1:2004+A1:2013, EN 1992-1-1:2004+A1:2014, EN 1990:2002+A1:2005 |
| Pins | Steel connections | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-8:2005 |
| Plain Concrete | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Portal Frame | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005 |
| Portal Knee | Steel connections | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-8:2005, EN 1993-1-1:2005+A1:2014 |
| Post Footing | Footings | - | IBC 2018 | NBC 2020 | EN 1997-1:2004+A1:2013 |
| Propped Beam | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005 |
| Punching Shear | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Purlin & Girt Loads | Wind actions | AS 4100:2020 | ASCE/SEI 7-22, ANSI/AISC 360-22 | NBC 2020, CSA S16-19 | EN 1991-1-4:2005+A1:2010, EN 1993-1-1:2005+A1:2014 |
| Rainfall Intensity (AEP) | Drainage | ARR 2019, AS/NZS 3500.3 | NOAA Atlas 14, IPC 2018, ASCE/SEI 7-22 | NBC 2020, NPC 2020 | EN 12056-3, EN 752 |
| Rainfall Intensity (ARI) | Drainage | AS/NZS 3500.3 | NOAA Atlas 14, IPC 2018, ASCE/SEI 7-22 | NBC 2020, NPC 2020 | EN 12056-3, EN 752 |
| Reinforcement Table | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19, CSA G30.18 | EN 1992-1-1:2004+A1:2014, EN 10080 |
| Residential Slab | Retaining walls and slabs | AS 2870:2011 | IBC 2018, IRC 2018, ACI CODE-318-25 | NBC 2020, CSA A23.1-19, CSA A23.3-19 | EN 1992-1-1:2004+A1:2014, EN 1997-1:2004+A1:2013, EN 1990:2002+A1:2005 |
| Retaining Wall | Retaining walls and slabs | AS 4678:2002, AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1997-1:2004+A1:2013, EN 1992-1-1:2004+A1:2014 |
| Roof Beam | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005 |
| Section Properties | Analysis | AS/NZS 3679.1 | - | - | - |
| Shelf Angle | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014, EN 1993-1-8:2005 |
| Sleeper Wall | Retaining walls and slabs | AS 4678:2002 | IBC 2018, ANSI/AWC NDS-2018, ANSI/AISC 360-22 | NBC 2020, CSA O86-19, CSA S16-19 | EN 1997-1:2004+A1:2013, EN 1993-1-1:2005+A1:2014, EN 1995-1-1:2004+A2:2014 |
| Snow Loads | Snow actions | AS/NZS 1170.3:2003 | ASCE/SEI 7-22 | NBC 2020 | EN 1991-1-3:2003+A1:2015 |
| Stair | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Static Analysis | Earthquake actions | AS 1170.4:2007 | ASCE/SEI 7-22 | NBC 2020 | EN 1998-1:2004+A1:2013 |
| Steel Column | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005 |
| Steel Member | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005 |
| Steel Member in Fire | Fire design | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-2:2005 |
| Stormwater Detention | Drainage | AS/NZS 3500 | - | - | EN 752 |
| Strip Footing | Footings | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1997-1:2004+A1:2013, EN 1992-1-1:2004+A1:2014, EN 1990:2002+A1:2005 |
| Strut & Tie | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Symbols | Utilities | - | - | - | - |
| T / Angle Lintel | Steel members | AS 4100:2020, AS 3700:2018 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014, EN 1996-1-1:2005+A1:2012 |
| Taper Haunch | Steel connections | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014 |
| Tension Member | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005, EN 1993-1-8:2005 |
| Terrain Change | Wind actions | AS/NZS 1170.2:2021 | ASCE/SEI 7-22 | NBC 2020 | EN 1991-1-4:2005+A1:2010 |
| Timber Column | Timber | AS 1720.1:2010 | ANSI/AWC NDS-2018 | CSA O86-19 | EN 1995-1-1:2004+A2:2014, EN 1990:2002+A1:2005 |
| Timber Floor Beam | Timber | AS 1720.1:2010 | ANSI/AWC NDS-2018 | CSA O86-19 | EN 1995-1-1:2004+A2:2014, EN 1990:2002+A1:2005 |
| Timber Member | Timber | AS 1720.1:2010 | ANSI/AWC NDS-2018 | CSA O86-19 | EN 1995-1-1:2004+A2:2014, EN 1990:2002+A1:2005 |
| Timber Member in Fire | Fire design | AS 1720.4:2019 | ANSI/AWC NDS-2018 | CSA O86-19 | EN 1995-1-2:2004 |
| Timber Roof Beam | Timber | AS 1720.1:2010 | ANSI/AWC NDS-2018 | CSA O86-19 | EN 1995-1-1:2004+A2:2014, EN 1990:2002+A1:2005 |
| Tree Effects: Piers | Footings | AS 2870:2011, AS 2159:2009 | - | - | - |
| Tree Effects: y_s | Retaining walls and slabs | AS 2870:2011 | - | - | - |
| Two-Way Slab | Concrete | AS 3600:2018 | ACI CODE-318-25 | CSA A23.3-19 | EN 1992-1-1:2004+A1:2014 |
| Unit Conversions | Utilities | - | - | - | - |
| Web Bearing | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005, EN 1993-1-5:2006 |
| Weld Group | Steel members | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-8:2005 |
| Welds | Steel connections | AS 4100:2020 | ANSI/AISC 360-22 | CSA S16-19 | EN 1993-1-8:2005 |
| Wind Actions | Wind actions | AS/NZS 1170.2:2021 | ASCE/SEI 7-22 | NBC 2020 | EN 1991-1-4:2005+A1:2010 |
Aluminium and bridge design modules are not part of TensorNode yet. Aluminium and prestressing materials can be used in the FEA Tool and the section designer. Modules for each code system are listed on the design codes page.