TensorNodeStart free trial

FEA Tool manual › Chapter 3

Coordinate systems and conventions

Chapters
  1. 1 Getting started
  2. 2 The interface
  3. 3 Coordinate systems and conventions
  4. 4 Modelling
  5. 5 Materials
  6. 6 Sections
  7. 7 Supports, releases and modifiers
  8. 8 Loads
  9. 9 Load combinations
  10. 10 Meshing
  11. 11 Static analysis
  12. 12 Dynamic and seismic analysis
  13. 13 Results
  14. 14 Design
  15. 15 Scripting and the AI model builder
  16. 16 Import and export
  17. 17 Verification
  18. 18 Scope and limits
  19. 19 Troubleshooting
  20. 20 Glossary and notation
On this page
  1. 3.1 Global coordinate system
  2. 3.2 Local axes of frame members
  3. 3.3 Member internal forces
  4. 3.4 Local axes of areas
  5. 3.5 Area forces and stresses
  6. 3.6 Units in the analysis

Every input and result of the FEA Tool refers to one of three coordinate systems: the global system of the model, the local system of each frame member, and the local system of each area. This chapter defines them, gives the sign conventions of the member and area forces, and lists the units the analysis works in.

3.1 Global coordinate system

The global system is right-handed with axes X, Y and Z. Z is vertical and points up, so gravity acts along −Z. Plan views look down the Z axis; Elevation X looks along Y at the X-Z plane and Elevation Y looks along X at the Y-Z plane.

Each node has six degrees of freedom in global axes: the translations uxu_x, uyu_y, uzu_z and the rotations rxr_x, ryr_y, rzr_z, positive by the right-hand rule. Joint loads, support reactions, nodal displacements and node springs are all given in global axes. A reaction is the force that the support applies to the structure.

Models imported from programs that use Y as the vertical axis are turned on import so that Z is up (Chapter 16).

3.2 Local axes of frame members

A frame member from node ii to node jj has local axes 1, 2 and 3:

  • Axis 1 runs along the member from ii to jj:
e1=xj−xiL(3.1)\mathbf{e}_1 = \frac{\mathbf{x}_j - \mathbf{x}_i}{L} \tag{3.1}

where xi\mathbf{x}_i and xj\mathbf{x}_j are the node coordinates and LL the member length.

  • Axis 2 lies in the vertical plane through the member and points upwards. For a member that is not vertical,
e2=Z−(Z⋅e1) e1∥Z−(Z⋅e1) e1∥(3.2)\mathbf{e}_2 = \frac{\mathbf{Z} - (\mathbf{Z}\cdot\mathbf{e}_1)\,\mathbf{e}_1}{\left\lVert \mathbf{Z} - (\mathbf{Z}\cdot\mathbf{e}_1)\,\mathbf{e}_1 \right\rVert} \tag{3.2}

with Z\mathbf{Z} the unit vector of global Z. A member is treated as vertical when its horizontal projection is less than 0.001L0.001L; its axis 2 is then global +X.

  • Axis 3 completes the right-handed set:
e3=e1×e2(3.3)\mathbf{e}_3 = \mathbf{e}_1 \times \mathbf{e}_2 \tag{3.3}

For a horizontal beam running along +X, axis 2 is +Z and axis 3 is −Y. For a column running up, axis 2 is +X and axis 3 is +Y.

Roll angle. The roll angle β\beta (degrees) turns axes 2 and 3 about axis 1 by the right-hand rule:

e2′=cos⁡β e2+sin⁡β e3,e3′=−sin⁡β e2+cos⁡β e3(3.4)\mathbf{e}_2' = \cos\beta\,\mathbf{e}_2 + \sin\beta\,\mathbf{e}_3, \qquad \mathbf{e}_3' = -\sin\beta\,\mathbf{e}_2 + \cos\beta\,\mathbf{e}_3 \tag{3.4}

Section orientation. Axis 3 is the major axis of a section. The depth of an I section lies along local 2, so its strong-axis second moment of area is I33I_{33} and bending about axis 3 (M3M_3) is major-axis bending. The weak-axis value is I22I_{22}. The shear area along axis 2, As2A_{s2}, is the web area of an I section. To turn a column so that its web lies along global Y, set β=90°\beta = 90°.

Options > Show local axes of frames draws the three axes on every member (1 red, 2 green, 3 blue).

3.3 Member internal forces

The internal forces of a member are given at stations along axis 1 in local axes:

SymbolMeaning
PPaxial force, positive in tension
V2V_2, V3V_3shear forces along local 2 and local 3
TTtorsion about local 1
M2M_2, M3M_3bending moments about local 2 and local 3

The convention is the positive-face convention: on the face of a cut whose outward normal points along +1, a positive force acts in the positive local direction and a positive moment acts about the positive local axis by the right-hand rule. On the opposite face the positive directions are reversed. Two consequences are worth remembering:

  • M3M_3 is positive when a horizontal beam sags under gravity, that is with tension at its bottom face;
  • the shears follow from the moments as
V2=−dM3dx,V3=dM2dx(3.5)V_2 = -\frac{dM_3}{dx}, \qquad V_3 = \frac{dM_2}{dx} \tag{3.5}

where xx is measured along axis 1 from node ii.

Stations run along the flexible length of the member from node ii (Section 7.5 describes rigid end offsets). Eleven stations are used by default. Where a point load acts, its station appears twice, just left and just right of the load, so that the jump in shear is shown exactly. Member deflections at the stations are given in local axes as d1d_1, d2d_2, d3d_3.

3.4 Local axes of areas

An area defined by nodes n1,n2,…,nkn_1, n_2, \ldots, n_k has its own local axes:

  • Axis 3 is the normal given by the right-hand rule on the order of the nodes: looking from the +3 side, the nodes run anticlockwise.
  • Axis 1 runs from node n1n_1 to node n2n_2, projected onto the plane of the area.
  • Axis 2 completes the set, e2=e3×e1\mathbf{e}_2 = \mathbf{e}_3 \times \mathbf{e}_1.

The +3 face of an area is called the top face and the −3 face the bottom face. Every element of an area's mesh uses the axes of its area, so the results of one area can be read in one set of directions. To reverse the normal of an area, list its nodes in the reverse order.

3.5 Area forces and stresses

Area results are forces and moments per unit width, in the area's local axes:

SymbolUnitMeaning
F11F_{11}, F22F_{22}kN/mmembrane direct forces, positive in tension
F12F_{12}kN/mmembrane shear force
M11M_{11}, M22M_{22}kNm/mbending moments; positive gives tension at the bottom (−3) face
M12M_{12}kNm/mtwisting moment
V13V_{13}, V23V_{23}kN/mtransverse shear forces

M11M_{11} is the moment that produces direct stress along axis 1, so it is resisted by reinforcement running along axis 1. In the results panel the same components are labelled with x and y for axes 1 and 2 (for example MxxM_{xx} for M11M_{11}).

The stresses at the top and bottom faces of a shell of thickness tt follow from the stress resultants:

σtop=Ft−6Mt2,σbot=Ft+6Mt2(3.6)\sigma_{\text{top}} = \frac{F}{t} - \frac{6M}{t^2}, \qquad \sigma_{\text{bot}} = \frac{F}{t} + \frac{6M}{t^2} \tag{3.6}

for each of the components 11, 22 and 12, with stresses in MPa and tension positive. The von Mises stress and the principal stresses at each face are formed from these.

3.6 Units in the analysis

The analysis engine works in one consistent set of units:

QuantityUnit
lengthm
forcekN
momentkNm
distributed loadkN/m (line), kN/m² (area)
modulus and strength of a materialMPa
densitykg/m³
masst (tonne)
times
temperature change°C
thermal expansion coefficient1/°C
section propertiesm², m⁴, m³, m⁶

The display units (Section 2.8) change only how values are shown and typed. Where a form or a script asks for a section dimension, a value above 5 is read as millimetres and a smaller value as metres; for a thickness of an area, the limit is 0.5. The form label always states the unit in use.