TensorNodeStart free trial

Welds design check for AS 4100, AISC 360, CSA S16 and Eurocode 3

Fillet weld capacity to AS 4100 §9.7.3.

Create a free account to use it

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.

What it checks

Design throat from the leg size, the capacity per unit length for the electrode and weld category (SP/GP), and the check against the resultant design force per unit length.

Inputs

Welds takes 5 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.

InputUnitDefault
Weld
Fillet leg size twmm8
Electrode Options: E43XX (430); E49XX (490); E55XX (550).-E49XX (490)
Weld category Options: SP (φ = 0.8); GP (φ = 0.6).-SP (φ = 0.8)
Effective weld length Lmm200
Actions
Resultant design force F*kN200

Results and report

The module reports: Leg / throat; Electrode / category; Capacity per length φvw; Design force per length v*; Total joint capacity φvw·L.

It checks: Fillet weld (per unit length); Total weld force.

Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.

Example with the default inputs

Welds with its default inputs for the Australia and New Zealand code system. The main inputs:

InputValue
Fillet leg size tw8 mm
ElectrodeE49XX (490)
Weld categorySP (φ = 0.8)
Effective weld length L200 mm
Resultant design force F*200 kN

Headline results:

ResultValue
Leg / throat8 / 5.7 mm
Electrode / categoryE49 / SP (φ 0.8)
Capacity per length φvw1.330 kN/mm
Design force per length v*1.000 kN/mm
Total joint capacity φvw·L266.1 kN

Governing check: Fillet weld (per unit length) (AS 4100 §9.7.3.10), v* 1.000 kN/mm against φvw 1.330 kN/mm, utilisation 0.75, passes.

Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.

Design codes

Welds works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.

RegionStandard and edition
Australia and New ZealandAS 4100:2020
United StatesANSI/AISC 360-22
CanadaCSA S16-19
EuropeEN 1993-1-8:2005

This module is one of the 21 basic calculators of the Free plan (one code system, reports carry an Evaluation mark), and it opens fully during the 7-day trial. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.

Related modules

  • Anchor Bolt
    Fastening to concrete (cast-in or post-installed anchor group) to AS 5216
  • Base Plate
    Steel column base plate to AS 3600 §12.6 and AS 4100
  • Bolts
    Single high-strength bolt capacity to AS 4100 §9.3
  • Cleat Plate
    Fin/cleat shear connection to AS 4100 §9
  • End Plate
    Bolted moment end-plate connection to AS 4100 §9
  • Pins
    Pin connection to AS 4100 §9.4
  • Portal Knee
    Bolted moment end-plate at a portal-frame knee
  • Taper Haunch
    Tapered haunch at a portal-frame knee

All connection design modules

Open Welds with a free account

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.