Pins design check for AS 4100, AISC 360, CSA S16 and Eurocode 3
Pin connection to AS 4100 §9.4.
Create a free account to use it
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.
What it checks
The pin in shear (one or more shear planes), bearing between the pin and the connected plies, and pin bending from the ply spacing.
Inputs
Pins takes 12 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.
| Input | Unit | Default |
|---|---|---|
| Pin | ||
| Pin diameter df | mm | 30 |
| Pin yield fyp | MPa | 250 |
| Shear planes Options: Single shear; Double shear. | - | Double shear |
| Hole clearance (hole diameter less d_f) | mm | 1 |
| Plies | ||
| Bearing ply thickness tp (ply carrying V*) | mm | 12 |
| Outer ply thickness t_o (each, carrying V*/2) | mm | 8 |
| Ply spacing a: centre to centre of the outer plies (double shear) or of the two plies (single shear) | mm | 24 |
| Ply width at the pin hole w | mm | 100 |
| Ply edge distance a_e (hole edge to ply end along the force, plus d_f/2) | mm | 60 |
| Ply tensile strength f_up | MPa | 410 |
| Ply yield stress f_y | MPa | 250 |
| Actions | ||
| Design shear V* | kN | 100 |
Results and report
The module reports: Pin; Pin area Ap; Shear capacity φVf; Bearing capacity φVb; Bending φM; Ply bearing and tear-out φVb (inner ply); Outer ply: pin bearing / ply bearing and tear-out; Hole, gap between plies.
It checks: Pin shear; Pin/ply bearing; Pin bending; Ply in bearing and tear-out; Pin bearing on each outer ply; Outer ply in bearing and tear-out.
Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.
Example with the default inputs
Pins with its default inputs for the Australia and New Zealand code system. The main inputs:
| Input | Value |
|---|---|
| Pin diameter df | 30 mm |
| Pin yield fyp | 250 MPa |
| Shear planes | Double shear |
| Hole clearance (hole diameter less d_f) | 1 mm |
| Bearing ply thickness tp (ply carrying V*) | 12 mm |
| Outer ply thickness t_o (each, carrying V*/2) | 8 mm |
| Ply spacing a: centre to centre of the outer plies (double shear) or of the two plies (single shear) | 24 mm |
| Ply width at the pin hole w | 100 mm |
Headline results:
| Result | Value |
|---|---|
| Pin | ⌀30 fy 250 mm / MPa |
| Pin area Ap | 707 mm² |
| Shear capacity φVf | 175.3 kN |
| Bearing capacity φVb | 100.8 kN |
| Bending φM | 900 (M* 600) kNmm |
| Ply bearing and tear-out φVb (inner ply) | 265.7 kN |
Governing check: Pin/ply bearing (AS 4100 §9.4.2), V* 100.0 kN against φVb 100.8 kN, utilisation 0.99, passes.
Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.
Design codes
Pins works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.
| Region | Standard and edition |
|---|---|
| Australia and New Zealand | AS 4100:2020 |
| United States | ANSI/AISC 360-22 |
| Canada | CSA S16-19 |
| Europe | EN 1993-1-8:2005 |
Use it in full during the 7-day trial of the Professional plan. Paid plans give access to the module packs. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.
Related modules
- Anchor Bolt
Fastening to concrete (cast-in or post-installed anchor group) to AS 5216 - Base Plate
Steel column base plate to AS 3600 §12.6 and AS 4100 - Bolts
Single high-strength bolt capacity to AS 4100 §9.3 - Cleat Plate
Fin/cleat shear connection to AS 4100 §9 - End Plate
Bolted moment end-plate connection to AS 4100 §9 - Portal Knee
Bolted moment end-plate at a portal-frame knee - Taper Haunch
Tapered haunch at a portal-frame knee - Welds
Fillet weld capacity to AS 4100 §9.7.3
Open Pins with a free account
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.