Cleat Plate design check for AS 4100, AISC 360, CSA S16 and Eurocode 3
Fin/cleat shear connection to AS 4100 §9.
Create a free account to use it
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.
What it checks
The eccentric bolt group (direct shear + torsion from the eccentricity), bolt bearing on the cleat, the cleat in shear yield and net-section rupture, and the support weld for V plus the eccentric moment.
Inputs
Cleat Plate takes 12 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.
| Input | Unit | Default |
|---|---|---|
| Actions | ||
| Design shear V* | kN | 150 |
| Geometry | ||
| Eccentricity e (bolt-line to weld) | mm | 60 |
| Bolts | ||
| Bolt size Options: M16; M20; M24. | - | M20 |
| Bolt grade Options: 4.6; 8.8. | - | 8.8 |
| Number of bolts (1 line) | - | 3 |
| Bolt pitch | mm | 70 |
| Cleat | ||
| Cleat depth dp | mm | 200 |
| Cleat thickness tpl | mm | 10 |
| Cleat yield fyp | MPa | 300 |
| Cleat tensile fup | MPa | 440 |
| Edge distance (bolt to cleat edge) | mm | 40 |
| Weld leg | mm | 6 |
Results and report
The module reports: Edge distance a_e / min; Polar I_p; Direct Fv / torsion Fh; Resultant on critical bolt; Cleat shear yield φVy; Cleat shear rupture φVn; Weld capacity.
It checks: Critical bolt (direct + torsion); Bolt bearing on cleat; Cleat shear yield; Cleat shear rupture (net); Weld to support; Minimum edge distance.
Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.
Example with the default inputs
Cleat Plate with its default inputs for the Australia and New Zealand code system. The main inputs:
| Input | Value |
|---|---|
| Design shear V* | 150 kN |
| Eccentricity e (bolt-line to weld) | 60 mm |
| Bolt size | M20 |
| Bolt grade | 8.8 |
| Number of bolts (1 line) | 3 |
| Bolt pitch | 70 mm |
| Cleat depth dp | 200 mm |
| Cleat thickness tpl | 10 mm |
Headline results:
| Result | Value |
|---|---|
| Edge distance a_e / min | 40 / 35 mm |
| Polar I_p | 9800 mm² |
| Direct Fv / torsion Fh | 50.0 / 64.3 kN |
| Resultant on critical bolt | 81.4 (φVf 93) kN |
| Cleat shear yield φVy | 324.0 kN |
| Cleat shear rupture φVn | 318.4 kN |
Governing check: Minimum edge distance (AS 4100 §9.6.2), a_e 40 mm provided against a_e,min 1.75·d_f = 35 mm, utilisation 0.88, passes.
Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.
Design codes
Cleat Plate works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.
| Region | Standard and edition |
|---|---|
| Australia and New Zealand | AS 4100:2020 |
| United States | ANSI/AISC 360-22 |
| Canada | CSA S16-19 |
| Europe | EN 1993-1-8:2005 |
Use it in full during the 7-day trial of the Professional plan. Paid plans give access to the module packs. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.
Related modules
- Anchor Bolt
Fastening to concrete (cast-in or post-installed anchor group) to AS 5216 - Base Plate
Steel column base plate to AS 3600 §12.6 and AS 4100 - Bolts
Single high-strength bolt capacity to AS 4100 §9.3 - End Plate
Bolted moment end-plate connection to AS 4100 §9 - Pins
Pin connection to AS 4100 §9.4 - Portal Knee
Bolted moment end-plate at a portal-frame knee - Taper Haunch
Tapered haunch at a portal-frame knee - Welds
Fillet weld capacity to AS 4100 §9.7.3
Open Cleat Plate with a free account
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.