TensorNodeStart free trial

Base Plate design check for AS 3600, AISC DG 1 (2nd ed.), CSA S16 and Eurocode 3

Steel column base plate to AS 3600 §12.6 and AS 4100.

Create a free account to use it

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.

What it checks

Concrete bearing with confinement √(A2/A1), plate flexure (thickness), and holding-down bolts in shear and (under uplift) tension, using a rectangular bearing stress-block at any eccentricity.

Inputs

Base Plate takes 17 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.

InputUnitDefault
Column
Column section type Options: UC; UB; SHS; RHS.-UC
Column section-250UC72.9
Actions
Axial N* (compression)kN1000
Axial tension Nt* (uplift)kN0
Shear V*kN40
Apply AS 4100 Cl 9.1.4 minimums Options: Yes; No.-Yes
Plate
Plate width Bmm400
Plate length Dpmm400
Plate thickness tpmm28
Plate yield fypMPa250
Concrete
Concrete f'cMPa25
Edge to footing ⊥ web ebimm70
Edge to footing ⊥ flange edimm110
HD bolts
HD bolt size Options: M20; M24; M30; M36.-M24
HD bolt grade Options: 4.6; 8.8.-8.8
Number of HD bolts-4
Bolt gauge Sg (⊥ web)mm130

Results and report

The module reports: Column section; Concrete bearing capacity φNc; Required plate thickness t_req / provided t_p; HD bolt group shear / tension capacity.

It checks: Concrete bearing; Base plate: compression; HD bolts: shear (group).

Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.

Example with the default inputs

Base Plate with its default inputs for the Australia and New Zealand code system. The main inputs:

InputValue
Column section typeUC
Column section250UC72.9
Axial N* (compression)1000 kN
Axial tension Nt* (uplift)0 kN
Shear V*40 kN
Apply AS 4100 Cl 9.1.4 minimumsYes
Plate width B400 mm
Plate length Dp400 mm

Headline results:

ResultValue
Column section250UC72.9 (UC)
Design axial N* (incl. AS 4100 Cl 9.1.4 minimum)1000 kN
Concrete bearing capacity φNc2916 (φNc1 2916 / φNc2 4320) kN
Plate cantilever lengths a_m (outstand) / a3 (H yield-line)98.4 / 44.1 mm
Plate bending capacity φNs = min(φNs1, φNs2)1457 (φNs1 1457 / φNs2 1676) kN
Required plate thickness t_req / provided t_p23.2 / 28 mm

Governing check: Base plate: compression (AS 4100 Cl 9.1.4 + plate bending · ASI DG4), Nc* 1000 kN (t_req 23.2 mm) against φNs 1457 kN (t_p 28 mm), utilisation 0.69, passes.

Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.

Design codes

Base Plate works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.

RegionStandard and edition
Australia and New ZealandAS 3600:2018, AS 4100:2020
United StatesAISC DG 1 (2nd ed.), ANSI/AISC 360-22
CanadaCSA S16-19, CSA A23.3-19
EuropeEN 1993-1-8:2005, EN 1992-1-1:2004+A1:2014

This module is one of the 21 basic calculators of the Free plan (one code system, reports carry an Evaluation mark), and it opens fully during the 7-day trial. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.

Related modules

  • Anchor Bolt
    Fastening to concrete (cast-in or post-installed anchor group) to AS 5216
  • Bolts
    Single high-strength bolt capacity to AS 4100 §9.3
  • Cleat Plate
    Fin/cleat shear connection to AS 4100 §9
  • End Plate
    Bolted moment end-plate connection to AS 4100 §9
  • Pins
    Pin connection to AS 4100 §9.4
  • Portal Knee
    Bolted moment end-plate at a portal-frame knee
  • Taper Haunch
    Tapered haunch at a portal-frame knee
  • Welds
    Fillet weld capacity to AS 4100 §9.7.3

All connection design modules

Open Base Plate with a free account

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.