Development & Laps design check for AS 3600, ACI 318, CSA A23.3 and Eurocode 2
Reinforcement development and lap lengths to AS 3600 §13.
Create a free account to use it
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.
What it checks
Basic tension development length Lsy.tb (with the bar-position, cover/confinement and concrete-strength factors), compression development, and tension/compression lap lengths.
Inputs
Development & Laps takes 6 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.
| Input | Unit | Default |
|---|---|---|
| Bar | ||
| Bar diameter db | mm | 16 |
| Bar position Options: Other (k1 = 1.0); Top bar, >300 mm below (k1 = 1.3). | - | Other (k1 = 1.0) |
| Geometry | ||
| Cover to bar cd | mm | 40 |
| Provided bar length (0 = size only) | mm | 0 |
| Material | ||
| Concrete f'c | MPa | 32 |
| Steel fsy | MPa | 500 |
Results and report
The module reports: Tension development Lsy.tb; Compression development Lsy.tbc; Tension lap; Compression lap.
It checks: Tension development L_sy.tb; Compression development L_sy.tbc; Compression lap splice.
Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.
Example with the default inputs
Development & Laps with its default inputs for the Australia and New Zealand code system. The main inputs:
| Input | Value |
|---|---|
| Bar diameter db | 16 mm |
| Bar position | Other (k1 = 1.0) |
| Cover to bar cd | 40 mm |
| Provided bar length (0 = size only) | 0 mm |
| Concrete f'c | 32 MPa |
| Steel fsy | 500 MPa |
Headline results:
| Result | Value |
|---|---|
| k1 (position) | 1.00 |
| k2 = (132−db)/100 | 1.160 |
| k3 (cover/confinement) | 0.775 |
| Tension development Lsy.tb | 472 mm |
| Compression development Lsy.tbc | 348 mm |
| Tension lap | 591 mm |
Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.
Design codes
Development & Laps works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.
| Region | Standard and edition |
|---|---|
| Australia and New Zealand | AS 3600:2018 |
| United States | ACI CODE-318-25 |
| Canada | CSA A23.3-19 |
| Europe | EN 1992-1-1:2004+A1:2014 |
This module is one of the 21 basic calculators of the Free plan (one code system, reports carry an Evaluation mark), and it opens fully during the 7-day trial. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.
Related modules
- Beam Shear
Reinforced-concrete beam shear to AS 3600 §8.2 - Beam Torsion
Reinforced-concrete beam torsion to AS 3600:2018 Cl. - Column Biaxial
RC column under axial load with biaxial bending to AS 3600 §10.6.3, the P-M interaction is built by strain compatibility about each axis, with reinforcement placed on all four faces (top/bottom bars resist X-axis bending, side bars resist Y-axis bending, both - Column Interaction
Rectangular reinforced-concrete column to AS 3600 §10 - Concrete Durability and Cover
Durability and cover to reinforcement to AS 3600:2018 Section 4 - Concrete Wall
RC wall in compression by the AS 3600 §11.5.3 simplified method - Corbel / Bracket
Reinforced-concrete corbel / bracket to AS 3600 - Crack Control
Crack control for RC beams/slabs by the AS 3600 §8.6.2.2 deemed-to-comply method
Open Development & Laps with a free account
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.