TensorNodeStart free trial
Home / Products / Concrete design / Column Biaxial

Column Biaxial design check for AS 3600, ACI 318, CSA A23.3 and Eurocode 2

Column Biaxial is a module of the concrete group, for Australia and New Zealand, United States, Canada and Europe.

Create a free account to use it

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.

What it checks

RC column under axial load with biaxial bending to AS 3600 §10.6.3, the P-M interaction is built by strain compatibility about each axis, with reinforcement placed on all four faces (top/bottom bars resist X-axis bending, side bars resist Y-axis bending, both.

Inputs

Column Biaxial takes 21 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.

InputUnitDefault
Width bmm400
Depth Dmm400
Bar diameter Options: N16; N20; N24; N28; N32.-N24
Bars per top/bottom face (resist Mx)-3
Bars per left/right face (resist My)-3
Covermm40
Ligature diameter Options: none; R10; N12; N16.-R10
Ligature spacingmm200
Skin reo bars (each face)-0
Effective length Lem3
Column bracing (AS 3600 10.3.1) Options: Braced; Unbraced (sway).-Braced
End moment ratio M1*/M2* (+ double curvature, −1 single)--1
β_d = G/(G+Q) of the axial load-0.6
Unbraced: storey ΣN*/ΣN_c (10.4.3(1); 0 = not known)-0
Unbraced: λ_uc from a frame buckling analysis (10.4.3(2); 0 = not used)-0
Skin bar dia Options: N12; N16.-N12
Concrete f'cMPa32
Steel fsyMPa500
Axial load N*kN1500
Moment M*xkNm120
Moment M*ykNm80

Results and report

The module reports: Classification; Squash load φNuo; φMux (at N*); φMuy (at N*); Exponent αn; Biaxial contour.

It checks: Axial squash; Uniaxial M about X (at N*); Column classification; Minimum reinforcement p_g; Maximum reinforcement p_g; Biaxial bending.

Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.

Example with the default inputs

Column Biaxial with its default inputs for the Australia and New Zealand code system. The main inputs:

InputValue
Width b400 mm
Depth D400 mm
Bar diameterN24
Bars per top/bottom face (resist Mx)3
Bars per left/right face (resist My)3
Cover40 mm
Ligature diameterR10
Ligature spacing200 mm

Headline results:

ResultValue
Steel 8·N24: p_g2.26% (Ast 3619 mm²)
ClassificationCompression-dominant (axial zone)
Squash load φNuo3941 kN
φMux (at N*)218.6 kNm
φMuy (at N*)218.6 kNm
Exponent αn1.40

Governing check: Ligature spacing ≤ min(0.5D, 300, D_c, 15d_b) (AS 3600 §8.3.2.2, §10.7.4.3), s 200 mm (2 legs N10) against ≤ 200 mm, utilisation 1.00, passes.

Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.

Design codes

Column Biaxial works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.

RegionStandard and edition
Australia and New ZealandAS 3600:2018
United StatesACI CODE-318-25
CanadaCSA A23.3-19
EuropeEN 1992-1-1:2004+A1:2014

Use it in full during the 7-day trial of the Professional plan. Paid plans give access to the module packs. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.

Related modules

All concrete design modules

Open Column Biaxial with a free account

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.