TensorNodeStart free trial
Home / Products / Foundation design / Combined Footing

Combined Footing design check for AS 3600, ACI 318, CSA A23.3 and Eurocode 7

Combined footing supporting two columns.

Create a free account to use it

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.

What it checks

The uniform bearing pressure, the longitudinal beam moments (hogging at the columns, sagging between), the transverse cantilever moment and the one-way shear, with reinforcement.

Inputs

Combined Footing takes 16 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.

InputUnitDefault
Loads
Column 1 load N1*kN600
Column 2 load N2*kN800
Geometry
Column spacingm4
Overhang past col 1m0.6
Overhang past col 2m0.6
Total footing length (0 = auto: overhangs + spacing)m0
Footing
Footing width Bm2.5
Footing depth Dmm750
Soil
Allowable bearingkPa250
Material
Concrete f'cMPa32
fsyMPa500
Reinforcement
Covermm70
Longit. bar diamm20
Longit. spacingmm150
Trans. bar diamm20
Trans. spacingmm200

Results and report

The module reports: Footing length L; Bearing pressure q; Longitudinal moment (gov); Transverse moment; Long. reinforcement.

It checks: Bearing pressure; One-way shear (longitudinal); Long Flexural capacity (stress-block); Long Minimum reinforcement; Long Section ductility k_u (Under-reinforced (ductile)); Long Tension steel yielding; Long Maximum reinforcement; Trans Flexural capacity (stress-block); Trans Minimum reinforcement; Trans Section ductility k_u (Under-reinforced (ductile)).

Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.

Example with the default inputs

Combined Footing with its default inputs for the Australia and New Zealand code system. The main inputs:

InputValue
Column 1 load N1*600 kN
Column 2 load N2*800 kN
Column spacing4 m
Overhang past col 10.6 m
Overhang past col 20.6 m
Total footing length (0 = auto: overhangs + spacing)0 m
Footing width B2.5 m
Footing depth D750 mm

Headline results:

ResultValue
Footing length L5.20 m
Bearing pressure q126 kPa
Longitudinal moment (gov)309 kNm
Transverse moment69 kNm/m
Long. reinforcement5236 mm²

Governing check: Trans Minimum reinforcement (AS 3600 §8.1.6), Ast,min 1175 mm²/m against Ast 1571 mm²/m, utilisation 0.75, passes.

Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.

Design codes

Combined Footing works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.

RegionStandard and edition
Australia and New ZealandAS 3600:2018
United StatesACI CODE-318-25
CanadaCSA A23.3-19
EuropeEN 1997-1:2004+A1:2013, EN 1992-1-1:2004+A1:2014, EN 1990:2002+A1:2005

Use it in full during the 7-day trial of the Professional plan. Paid plans give access to the module packs. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.

Related modules

  • Bored Pier
    Bored (CFA/cast-in-situ) pier
  • Eccentric Pad
    Eccentrically-loaded pad footing
  • Pad Foundation
    Factored loading with eccentricity, uplift, sliding and overturning; two-way reinforcement by mesh (SL/RL) or bar diameter + spacing.
  • Piered Beam
    Reinforced-concrete ground beam spanning between bored piers
  • Post Footing
    Embedded post footing driven by lateral load, applied moment, load height, footing width/depth and soil φ/γ (embedment depth governs).
  • Strip Footing
    Continuous strip footing under a wall line-load
  • Tree Effects: Piers
    Bored pier through a tree-affected reactive (drying/swelling) zone
  • Basement Wall
    Basement wall

All foundation design modules

Open Combined Footing with a free account

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.