Bolt Tension design check for AS 4100, AISC 360, CSA S16 and Eurocode 3
Bolt in tension with prying to AS 4100 §9.
Create a free account to use it
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.
What it checks
A T-stub model adds the prying force from the flexible connected plate to the applied tension; the bolt is checked for the total and the plate thickness for prying control.
Inputs
Bolt Tension takes 8 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.
| Input | Unit | Default |
|---|---|---|
| Bolt | ||
| Bolt size Options: M16; M20; M24; M30; M36. | - | M20 |
| Bolt grade Options: 4.6; 8.8; 10.9. | - | 8.8 |
| Actions | ||
| Applied tension per bolt T* | kN | 75 |
| Plate | ||
| Plate/flange thickness t | mm | 20 |
| Plate yield fy | MPa | 300 |
| Bolt-to-stem b | mm | 50 |
| Bolt-to-edge a | mm | 40 |
| Tributary pitch p | mm | 80 |
Results and report
The module reports: Bolt; Lever arms b' / a'; Prying force Q; Total bolt tension B; Plate limit on T* (two hinges).
It checks: Bolt tension incl. prying; Plate flexure with prying (two-hinge limit); Plate (prying control).
Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.
Example with the default inputs
Bolt Tension with its default inputs for the Australia and New Zealand code system. The main inputs:
| Input | Value |
|---|---|
| Bolt size | M20 |
| Bolt grade | 8.8 |
| Applied tension per bolt T* | 75 kN |
| Plate/flange thickness t | 20 mm |
| Plate yield fy | 300 MPa |
| Bolt-to-stem b | 50 mm |
| Bolt-to-edge a | 40 mm |
| Tributary pitch p | 80 mm |
Headline results:
| Result | Value |
|---|---|
| Bolt | M20 / 8.8 |
| Lever arms b' / a' | 40.0 / 50.0 mm |
| Prying force Q | 16.8 kN |
| Total bolt tension B | 91.8 (φNtf 163) kN |
| Thickness for Q=0 | 23.6 vs 20 mm |
| Plate limit on T* (two hinges) | 93.2 kN |
Governing check: Plate flexure with prying (two-hinge limit) (AS 4100 §9.1.8 · T-stub model), T* 75.0 kN against φ0.25p·t²f_y(1+δ)/b′ 93.2 kN, utilisation 0.81, passes.
Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.
Design codes
Bolt Tension works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.
| Region | Standard and edition |
|---|---|
| Australia and New Zealand | AS 4100:2020 |
| United States | ANSI/AISC 360-22 |
| Canada | CSA S16-19 |
| Europe | EN 1993-1-8:2005 |
Use it in full during the 7-day trial of the Professional plan. Paid plans give access to the module packs. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.
Related modules
- Bolt Group
Bolt group under shear plus an out-of-plane moment to AS 4100 §9 - Eccentric Bolt Group
Bolt group under in-plane eccentric shear (a bracket) to AS 4100 §9 - Weld Group
Fillet weld group under in-plane eccentric shear to AS 4100 §9.7 - Anchor Bolt
Fastening to concrete (cast-in or post-installed anchor group) to AS 5216 - Base Plate
Steel column base plate to AS 3600 §12.6 and AS 4100 - Bolts
Single high-strength bolt capacity to AS 4100 §9.3 - Cleat Plate
Fin/cleat shear connection to AS 4100 §9 - End Plate
Bolted moment end-plate connection to AS 4100 §9
Open Bolt Tension with a free account
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.