Steel Member design check for AS 4100, AISC 360, CSA S16 and Eurocode 3
Hot-rolled steel member (UB / UC / PFC / TFB) to AS 4100.
Create a free account to use it
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.
What it checks
Section moment, member lateral-torsional buckling, shear and section compression.
Inputs
Steel Member takes 8 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.
| Input | Unit | Default |
|---|---|---|
| Section | ||
| Section type Options: UB; UC; PFC; UBP; TFB; EA; UEA; CHS; +2 more. | - | UB |
| Section | - | 360UB56.7 |
| Geometry | ||
| Span L | m | 8 |
| Effective length Le (restraint spacing) | m | 2 |
| Moment factor αm | - | 1.13 |
| Loads | ||
| Design actions Options: From the span and the factored UDL w*; Enter M*, V* and N*. | - | From the span and the factored UDL w* |
| UDL w* | kN/m | 20 |
| Axial N* | kN | 0 |
Results and report
The module reports: Section; Depth × mass; fy / fu; Ze (effective); Section φMs; Member φMbx (LTB); Shear φVv; Compression φNs.
It checks: Section moment; Member moment (LTB); Compression (yield).
Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.
Example with the default inputs
Steel Member with its default inputs for the Australia and New Zealand code system. The main inputs:
| Input | Value |
|---|---|
| Section type | UB |
| Section | 360UB56.7 |
| Span L | 8 m |
| Effective length Le (restraint spacing) | 2 m |
| Moment factor αm | 1.13 |
| Design actions | From the span and the factored UDL w* |
| UDL w* | 20 kN/m |
| Axial N* | 0 kN |
Headline results:
| Result | Value |
|---|---|
| Section | 360UB56.7 (UB) |
| Depth × mass | 359 × 56.7 mm · kg/m |
| fy / fu | 300 / 440 MPa |
| Ze (effective) | 1.01×10⁶ mm³ |
| Section φMs | 272.7 kNm |
| Member φMbx (LTB) | 269.4 kNm |
Governing check: Member moment (LTB) (AS 4100 §5.6), M* 160.0 kNm against φMbx 269.4 kNm, utilisation 0.59, passes.
Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.
Design codes
Steel Member works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.
| Region | Standard and edition |
|---|---|
| Australia and New Zealand | AS 4100:2020 |
| United States | ANSI/AISC 360-22 |
| Canada | CSA S16-19 |
| Europe | EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005 |
This module is one of the 21 basic calculators of the Free plan (one code system, reports carry an Evaluation mark), and it opens fully during the 7-day trial. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.
Related modules
- Beam-Column
Steel member under combined axial compression and bending to AS 4100 §8 - Compression Strut
Axially-loaded steel member (strut / column) to AS 4100 - Crane Beam
Overhead-crane runway beam - Floor Beam
Simply-supported steel floor beam to AS 4100 - Load Stiffener
Load-bearing web stiffener to AS 4100 §5.14 - Mullion
Steel wall mullion / wind post to AS 4100 - PFC & Plate
Built-up beam from a PFC (parallel-flange channel) with a welded plate - Portal Frame
Single-bay portal frame to AS 4100
Open Steel Member with a free account
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.