PFC & Plate design check for AS 4100, AISC 360, CSA S16 and Eurocode 3
Built-up beam from a PFC (parallel-flange channel) with a welded plate.
Create a free account to use it
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.
What it checks
The combined section properties (about the composite neutral axis) and the section moment and shear capacities to AS 4100.
Inputs
PFC & Plate takes 7 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.
| Input | Unit | Default |
|---|---|---|
| PFC | ||
| PFC section Options: 200PFC22.9; 250PFC35.5; 300PFC40.1; 380PFC55.2. | - | 250PFC35.5 |
| Plate | ||
| Plate width bp | mm | 200 |
| Plate thickness tp | mm | 12 |
| Plate position Options: Top flange; Bottom flange. | - | Top flange |
| Material | ||
| Yield fy | MPa | 300 |
| Actions | ||
| Design moment M* | kNm | 60 |
| Design shear V* | kN | 80 |
Results and report
The module reports: Combined area A; Second moment I; Min section modulus; Moment capacity φMs; Shear capacity φVv.
It checks: Section moment capacity; Shear capacity (web).
Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.
Example with the default inputs
PFC & Plate with its default inputs for the Australia and New Zealand code system. The main inputs:
| Input | Value |
|---|---|
| PFC section | 250PFC35.5 |
| Plate width bp | 200 mm |
| Plate thickness tp | 12 mm |
| Plate position | Top flange |
| Yield fy | 300 MPa |
| Design moment M* | 60 kNm |
| Design shear V* | 80 kN |
Headline results:
| Result | Value |
|---|---|
| Combined area A | 6920 mm² |
| Second moment I | 72.0 ×10⁶ mm⁴ |
| Min section modulus | 423 (×1.17 vs PFC) ×10³ mm³ |
| Moment capacity φMs | 114.1 kNm |
| Shear capacity φVv | 324 kN |
Governing check: Section moment capacity (AS 4100 §5.2), M* 60.0 kNm against φMs 114.1 kNm, utilisation 0.53, passes.
Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.
Design codes
PFC & Plate works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.
| Region | Standard and edition |
|---|---|
| Australia and New Zealand | AS 4100:2020 |
| United States | ANSI/AISC 360-22 |
| Canada | CSA S16-19 |
| Europe | EN 1993-1-1:2005+A1:2014, EN 1993-1-8:2005 |
Use it in full during the 7-day trial of the Professional plan. Paid plans give access to the module packs. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.
Related modules
- Beam-Column
Steel member under combined axial compression and bending to AS 4100 §8 - Compression Strut
Axially-loaded steel member (strut / column) to AS 4100 - Crane Beam
Overhead-crane runway beam - Floor Beam
Simply-supported steel floor beam to AS 4100 - Load Stiffener
Load-bearing web stiffener to AS 4100 §5.14 - Mullion
Steel wall mullion / wind post to AS 4100 - Portal Frame
Single-bay portal frame to AS 4100 - Propped Beam
Steel propped cantilever to AS 4100
Open PFC & Plate with a free account
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.