TensorNodeStart free trial
Home / Products / Steel design / Compression Strut

Compression Strut design check for AS 4100, AISC 360, CSA S16 and Eurocode 3

Axially-loaded steel member (strut / column) to AS 4100.

Create a free account to use it

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.

What it checks

Section and member compression capacity with the §6.3.3 slenderness reduction, plus minor-axis and combined (biaxial) bending.

Inputs

Compression Strut takes 10 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.

InputUnitDefault
Section
Section type Options: UC; UB; PFC; SHS; RHS; CHS; EA; UEA.-UC
Section-200UC59.5
Geometry
Actual length about Xm3
End fixity about X (ke) Options: Pinned-Pinned (1.0); Fixed-Pinned (0.85); Fixed-Fixed (0.70); Fixed-Free / cantilever (2.2); Braced sway (1.2); Sway (2.0).-Pinned-Pinned (1.0)
Actual length about Ym3
End fixity about Y (ke) Options: Pinned-Pinned (1.0); Fixed-Pinned (0.85); Fixed-Fixed (0.70); Fixed-Free / cantilever (2.2); Braced sway (1.2); Sway (2.0).-Pinned-Pinned (1.0)
Member constant αb Options: From the section type (Table 6.3.3); −1.0; −0.5; 0 (hot-rolled, kf=1); 0.5; 1.0.-From the section type (Table 6.3.3)
Actions
Axial N*kN1500
Major-axis M*xkNm40
Minor-axis M*ykNm0

Results and report

The module reports: Section; Section N_s; Effective length Le (x / y); λn (x / y); αc (governing); Member φNc; φMrx / φMry (reduced).

It checks: Member compression; Combined N + M about X.

Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.

Example with the default inputs

Compression Strut with its default inputs for the Australia and New Zealand code system. The main inputs:

InputValue
Section typeUC
Section200UC59.5
Actual length about X3 m
End fixity about X (ke)Pinned-Pinned (1.0)
Actual length about Y3 m
End fixity about Y (ke)Pinned-Pinned (1.0)
Member constant αbFrom the section type (Table 6.3.3)
Axial N*1500 kN

Headline results:

ResultValue
Section200UC59.5 (UC)
Section N_s2286 kN
Effective length Le (x / y)3.00 / 3.00 (ke 1.00/1.00) m
λn (x / y)37 / 64
αc (governing)0.788
Member φNc1621 kN

Governing check: Member compression (AS 4100 §6.3), N* 1500.0 kN against φNc 1621.4 kN, utilisation 0.93, passes.

Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.

Design codes

Compression Strut works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.

RegionStandard and edition
Australia and New ZealandAS 4100:2020
United StatesANSI/AISC 360-22
CanadaCSA S16-19
EuropeEN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005

This module is one of the 21 basic calculators of the Free plan (one code system, reports carry an Evaluation mark), and it opens fully during the 7-day trial. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.

Related modules

  • Beam-Column
    Steel member under combined axial compression and bending to AS 4100 §8
  • Crane Beam
    Overhead-crane runway beam
  • Floor Beam
    Simply-supported steel floor beam to AS 4100
  • Load Stiffener
    Load-bearing web stiffener to AS 4100 §5.14
  • Mullion
    Steel wall mullion / wind post to AS 4100
  • PFC & Plate
    Built-up beam from a PFC (parallel-flange channel) with a welded plate
  • Portal Frame
    Single-bay portal frame to AS 4100
  • Propped Beam
    Steel propped cantilever to AS 4100

All steel design modules

Open Compression Strut with a free account

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.