TensorNodeStart free trial
Home / Products / Steel design / Propped Beam

Propped Beam design check for AS 4100, AISC 360, CSA S16 and Eurocode 3

Steel propped cantilever to AS 4100.

Create a free account to use it

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.

What it checks

UDL with the fixed-end (hogging) and span (sagging) moments, the wall and prop reactions, the maximum shear at the fixed end, and the deflection limit.

Inputs

Propped Beam takes 7 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.

InputUnitDefault
Section
Section type Options: UB; UC; PFC.-UB
Section-360UB44.7
Geometry
Span Lm7
Lateral restraint Options: Full (slab/deck); At supports only; Custom Le.-Full (slab/deck)
Loads
Dead UDL GkN/m6
Live UDL QkN/m9
Moment modification αm-1.13

Results and report

The module reports: Section; Factored UDL w*; Fixed-end moment (hogging); Span moment (sagging); φMbx (member); Reactions (wall / prop); Deflection δ.

It checks: Section moment (fixed end); Member moment (LTB); Shear (at fixed end); Deflection.

Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.

Example with the default inputs

Propped Beam with its default inputs for the Australia and New Zealand code system. The main inputs:

InputValue
Section typeUB
Section360UB44.7
Span L7 m
Lateral restraintFull (slab/deck)
Dead UDL G6 kN/m
Live UDL Q9 kN/m
Moment modification αm1.13

Headline results:

ResultValue
Section360UB44.7 (UB)
Factored UDL w*20.7 kN/m
Fixed-end moment (hogging)126.8 kNm
Span moment (sagging)71.3 kNm
φMbx (member)221.8 kNm
Reactions (wall / prop)90.6 / 54.3 kN

Governing check: Section moment (fixed end) (AS 4100 §5.2.1), M* 126.8 kNm against φMs 221.8 kNm, utilisation 0.57, passes.

Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.

Design codes

Propped Beam works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.

RegionStandard and edition
Australia and New ZealandAS 4100:2020
United StatesANSI/AISC 360-22
CanadaCSA S16-19
EuropeEN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005

Use it in full during the 7-day trial of the Professional plan. Paid plans give access to the module packs. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.

Related modules

  • Beam-Column
    Steel member under combined axial compression and bending to AS 4100 §8
  • Compression Strut
    Axially-loaded steel member (strut / column) to AS 4100
  • Crane Beam
    Overhead-crane runway beam
  • Floor Beam
    Simply-supported steel floor beam to AS 4100
  • Load Stiffener
    Load-bearing web stiffener to AS 4100 §5.14
  • Mullion
    Steel wall mullion / wind post to AS 4100
  • PFC & Plate
    Built-up beam from a PFC (parallel-flange channel) with a welded plate
  • Portal Frame
    Single-bay portal frame to AS 4100

All steel design modules

Open Propped Beam with a free account

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.