Load Stiffener design check for AS 4100, AISC 360, CSA S16 and Eurocode 3
Load-bearing web stiffener to AS 4100 §5.14.
Create a free account to use it
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.
What it checks
A pair (or pairs) of stiffeners at a bearing/point load: the bearing-yield capacity and the buckling capacity of the stiffener-plus-web strut are checked against the applied reaction.
Inputs
Load Stiffener takes 8 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.
| Input | Unit | Default |
|---|---|---|
| Beam | ||
| Beam type Options: UB; UC. | - | UB |
| Beam section | - | 610UB125 |
| Stiffener | ||
| Stiffener outstand bs | mm | 100 |
| Stiffener thickness ts | mm | 16 |
| Corner clip at the web-flange root (0 = 15 mm) | mm | 0 |
| Number of plates | - | 2 |
| Stiffener yield fys | MPa | 300 |
| Actions | ||
| Reaction / load R* | kN | 600 |
Results and report
The module reports: Stiffener area n·b_s·t_s; Contact area A_s (bearing); Yield capacity φNs; Buckling capacity φNc; Strut slenderness λ; Reaction R*.
It checks: Stiffener yield (bearing); Stiffener buckling.
Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.
Example with the default inputs
Load Stiffener with its default inputs for the Australia and New Zealand code system. The main inputs:
| Input | Value |
|---|---|
| Beam type | UB |
| Beam section | 610UB125 |
| Stiffener outstand bs | 100 mm |
| Stiffener thickness ts | 16 mm |
| Corner clip at the web-flange root (0 = 15 mm) | 0 mm |
| Number of plates | 2 |
| Stiffener yield fys | 300 MPa |
| Reaction / load R* | 600 kN |
Headline results:
| Result | Value |
|---|---|
| Stiffener area n·b_s·t_s | 3200 mm² |
| Contact area A_s (bearing) | 2720 mm² |
| Yield capacity φNs | 734 kN |
| Buckling capacity φNc | 2128 kN |
| Strut slenderness λ | 10 |
| Reaction R* | 600 kN |
Governing check: Stiffener yield (bearing) (AS 4100 §5.14.1), R* 600 kN against φNs 734 kN (contact A_s 2720 mm²), utilisation 0.82, passes.
Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.
Design codes
Load Stiffener works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.
| Region | Standard and edition |
|---|---|
| Australia and New Zealand | AS 4100:2020 |
| United States | ANSI/AISC 360-22 |
| Canada | CSA S16-19 |
| Europe | EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005, EN 1993-1-5:2006 |
Use it in full during the 7-day trial of the Professional plan. Paid plans give access to the module packs. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.
Related modules
- Beam-Column
Steel member under combined axial compression and bending to AS 4100 §8 - Compression Strut
Axially-loaded steel member (strut / column) to AS 4100 - Crane Beam
Overhead-crane runway beam - Floor Beam
Simply-supported steel floor beam to AS 4100 - Mullion
Steel wall mullion / wind post to AS 4100 - PFC & Plate
Built-up beam from a PFC (parallel-flange channel) with a welded plate - Portal Frame
Single-bay portal frame to AS 4100 - Propped Beam
Steel propped cantilever to AS 4100
Open Load Stiffener with a free account
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.