TensorNodeStart free trial
Home / Products / Steel design / Portal Frame

Portal Frame design check for AS 4100, AISC 360, CSA S16 and Eurocode 3

Single-bay portal frame to AS 4100.

Create a free account to use it

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.

What it checks

The gravity and wind load cases give the knee and apex moments; the rafter and column (as beam-columns) are checked against their member moment capacities at the critical knee.

Inputs

Portal Frame takes 8 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.

InputUnitDefault
Frame
Frame spanm18
Eaves heightm6
Loads
Gravity load wkN/m8
Wind loadkN/m4
Members
Column section type Options: UB; UC; PFC; RHS; SHS.-UB
Column section-460UB74.6
Rafter section type Options: UB; UC; PFC; RHS; SHS.-UB
Rafter section-460UB74.6

Results and report

The module reports: Gravity moment; Wind moment; Knee moment (design); Column capacity φMbx; Rafter capacity φMbx.

It checks: Column (knee moment); Rafter (knee moment).

Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.

Example with the default inputs

Portal Frame with its default inputs for the Australia and New Zealand code system. The main inputs:

InputValue
Frame span18 m
Eaves height6 m
Gravity load w8 kN/m
Wind load4 kN/m
Column section typeUB
Column section460UB74.6
Rafter section typeUB
Rafter section460UB74.6

Headline results:

ResultValue
Gravity moment177 kNm
Wind moment38 kNm
Knee moment (design)214 kNm
Column capacity φMbx339 kNm
Rafter capacity φMbx339 kNm

Governing check: Column (knee moment) (AS 4100 §5/§8), M* 214 kNm against φMbx 339 kNm, utilisation 0.63, passes.

Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.

Design codes

Portal Frame works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.

RegionStandard and edition
Australia and New ZealandAS 4100:2020
United StatesANSI/AISC 360-22
CanadaCSA S16-19
EuropeEN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005

Use it in full during the 7-day trial of the Professional plan. Paid plans give access to the module packs. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.

Related modules

  • Beam-Column
    Steel member under combined axial compression and bending to AS 4100 §8
  • Compression Strut
    Axially-loaded steel member (strut / column) to AS 4100
  • Crane Beam
    Overhead-crane runway beam
  • Floor Beam
    Simply-supported steel floor beam to AS 4100
  • Load Stiffener
    Load-bearing web stiffener to AS 4100 §5.14
  • Mullion
    Steel wall mullion / wind post to AS 4100
  • PFC & Plate
    Built-up beam from a PFC (parallel-flange channel) with a welded plate
  • Propped Beam
    Steel propped cantilever to AS 4100

All steel design modules

Open Portal Frame with a free account

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.