Shelf Angle design check for AS 4100, AISC 360, CSA S16 and Eurocode 3
Shelf angle / masonry support angle to AS 4100.
Create a free account to use it
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.
What it checks
The eccentric brick load bends the angle leg; the leg bending capacity and the fixing-bolt shear back to the structure are checked per metre.
Inputs
Shelf Angle takes 8 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.
| Input | Unit | Default |
|---|---|---|
| Angle | ||
| Angle leg | mm | 150 |
| Angle thickness | mm | 12 |
| Yield fy | MPa | 300 |
| Loads | ||
| Masonry load | kN/m | 4 |
| Load eccentricity | mm | 50 |
| Fixings | ||
| Fixing spacing | m | 0.6 |
| Fixing bolt Options: M12; M16; M20. | - | M16 |
| Bolt grade Options: 4.6; 8.8. | - | 8.8 |
Results and report
The module reports: Load per metre; Eccentric moment; Leg capacity φMs; Bolt force; Fixing bolt.
It checks: Angle bending (eccentric); Fixing bolt shear.
Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.
Example with the default inputs
Shelf Angle with its default inputs for the Australia and New Zealand code system. The main inputs:
| Input | Value |
|---|---|
| Angle leg | 150 mm |
| Angle thickness | 12 mm |
| Yield fy | 300 MPa |
| Masonry load | 4 kN/m |
| Load eccentricity | 50 mm |
| Fixing spacing | 0.6 m |
| Fixing bolt | M16 |
| Bolt grade | 8.8 |
Headline results:
| Result | Value |
|---|---|
| Load per metre | 4.0 kN/m |
| Eccentric moment | 0.20 kNm/m |
| Leg capacity φMs | 6.48 kNm/m |
| Bolt force | 2.4 (φVf 59.3) kN |
| Fixing bolt | M16 |
Governing check: Fixing bolt shear (AS 4100 §9.3.2.1), V 2.4 kN against φVf 59.3 kN, utilisation 0.04, passes.
Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.
Design codes
Shelf Angle works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.
| Region | Standard and edition |
|---|---|
| Australia and New Zealand | AS 4100:2020 |
| United States | ANSI/AISC 360-22 |
| Canada | CSA S16-19 |
| Europe | EN 1993-1-1:2005+A1:2014, EN 1993-1-8:2005 |
Use it in full during the 7-day trial of the Professional plan. Paid plans give access to the module packs. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.
Related modules
- Beam-Column
Steel member under combined axial compression and bending to AS 4100 §8 - Compression Strut
Axially-loaded steel member (strut / column) to AS 4100 - Crane Beam
Overhead-crane runway beam - Floor Beam
Simply-supported steel floor beam to AS 4100 - Load Stiffener
Load-bearing web stiffener to AS 4100 §5.14 - Mullion
Steel wall mullion / wind post to AS 4100 - PFC & Plate
Built-up beam from a PFC (parallel-flange channel) with a welded plate - Portal Frame
Single-bay portal frame to AS 4100
Open Shelf Angle with a free account
7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.