TensorNodeStart free trial
Home / Products / Steel design / Roof Beam

Roof Beam design check for AS 4100, AISC 360, CSA S16 and Eurocode 3

Steel roof beam/rafter to AS 4100.

Create a free account to use it

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.

What it checks

Gravity (1.2G + 1.5Q) and net wind-uplift (0.9G + Wu) load cases, section and member moment, shear, and the imposed/wind deflection limits.

Inputs

Roof Beam takes 9 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.

InputUnitDefault
Section type Options: UB; UC; PFC; RHS; SHS.-UB
Section-360UB44.7
Span Lm8
Lateral restraint Options: At supports only; Full (sheeting); Custom Le.-At supports only
Dead UDL GkN/m3
Live/imposed UDL QkN/m1.5
Wind uplift WukN/m6
Fly-brace spacing on the bottom flange (0 = supports only)m0
Moment modification αm-1.13

Results and report

The module reports: Section; Gravity moment Mg; Uplift moment Mup; Design moment M*; φMbx (member); Imposed deflection; Wind deflection.

It checks: Section moment; Member moment (LTB); Imposed deflection; Wind deflection.

Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.

Example with the default inputs

Roof Beam with its default inputs for the Australia and New Zealand code system. The main inputs:

InputValue
Section typeUB
Section360UB44.7
Span L8 m
Lateral restraintAt supports only
Dead UDL G3 kN/m
Live/imposed UDL Q1.5 kN/m
Wind uplift Wu6 kN/m
Fly-brace spacing on the bottom flange (0 = supports only)0 m

Headline results:

ResultValue
Section360UB44.7 (UB)
Gravity moment Mg46.8 kNm
Uplift moment Mup26.4 kNm
Design moment M*46.8 (gravity) kNm
φMbx (member)59.1 kNm
Imposed deflection3.3 (L/250 32.0) mm

Governing check: Member moment (LTB) (AS 4100 §5.6), M* 46.8 kNm (gravity, top flange critical); 26.4 kNm (uplift, bottom flange critical) against φMbx 59.1 kNm; uplift φMbx 58.1 kNm at l_e = k_t·l = 1.014·8.00 m, utilisation 0.79, passes.

Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.

Design codes

Roof Beam works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.

RegionStandard and edition
Australia and New ZealandAS 4100:2020
United StatesANSI/AISC 360-22
CanadaCSA S16-19
EuropeEN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005

Use it in full during the 7-day trial of the Professional plan. Paid plans give access to the module packs. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.

Related modules

  • Beam-Column
    Steel member under combined axial compression and bending to AS 4100 §8
  • Compression Strut
    Axially-loaded steel member (strut / column) to AS 4100
  • Crane Beam
    Overhead-crane runway beam
  • Floor Beam
    Simply-supported steel floor beam to AS 4100
  • Load Stiffener
    Load-bearing web stiffener to AS 4100 §5.14
  • Mullion
    Steel wall mullion / wind post to AS 4100
  • PFC & Plate
    Built-up beam from a PFC (parallel-flange channel) with a welded plate
  • Portal Frame
    Single-bay portal frame to AS 4100

All steel design modules

Open Roof Beam with a free account

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.