TensorNodeStart free trial
Home / Products / Steel design / Composite Member

Composite Member design check for AS 2327, AISC 360, CSA S16 and Eurocode 4

Simply-supported composite steel-and-concrete beam to AS 2327.

Create a free account to use it

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.

What it checks

A library steel section acting compositely with a profiled-deck slab (Bondek / Condek / KingFlor / RF / solid), with the effective flange width, the plastic composite moment capacity, the degree of.

Inputs

Composite Member takes 12 inputs for the Australia and New Zealand code system, with the defaults below. Lengths are in m, forces in kN and stresses in MPa unless the unit column says otherwise.

InputUnitDefault
Steel
Steel section type Options: UB; UC; PFC.-UB
Section-410UB53.7
Geometry
Span Lm9
Beam spacingm3
Slab
Deck / slab type Options: Bondek (54); Condek (55); KingFlor KF57; KingFlor KF70; RF55; Solid slab.-Bondek (54)
Slab total depthmm130
Concrete f'cMPa32
Loads
Dead load GkPa4
Live load QkPa3
Connectors
Stud diameter Options: 16 mm; 19 mm; 22 mm.-19 mm
Studs per metre/m4
Stud f_uMPa450

Results and report

The module reports: Effective flange width b_cf; Concrete C / steel T; Composite capacity φMbc; Degree of shear connection β; Stud capacity / number (½ span).

It checks: Composite moment capacity; Degree of shear connection; Vertical shear (steel web).

Each module produces a report: numbered working, formulas with substituted values, tables and diagrams, ready to attach to a calculation package. The report carries a verification code that confirms it was made by TensorNode and has not been changed.

Example with the default inputs

Composite Member with its default inputs for the Australia and New Zealand code system. The main inputs:

InputValue
Steel section typeUB
Section410UB53.7
Span L9 m
Beam spacing3 m
Deck / slab typeBondek (54)
Slab total depth130 mm
Concrete f'c32 MPa
Dead load G4 kPa

Headline results:

ResultValue
Effective flange width b_cf2250 mm
Concrete C / steel T4651 / 2205 kN
Composite capacity φMbc526.4 (PNA in slab) kNm
Degree of shear connection β0.70
Stud capacity / number (½ span)85.6 kN × 18

Governing check: Degree of shear connection (AS 2327 §5.4), β 0.70 against ≥ 0.5, utilisation 0.72, passes.

Computed by TensorNode with the default inputs shown; a qualified engineer checks every result.

Design codes

Composite Member works to 4 code systems in Australia and New Zealand, United States, Canada and Europe. The standards and editions are listed below; clause numbers are cited in the report.

RegionStandard and edition
Australia and New ZealandAS 2327:2017
United StatesANSI/AISC 360-22
CanadaCSA S16-19
EuropeEN 1994-1-1:2004, EN 1993-1-1:2005+A1:2014, EN 1990:2002+A1:2005

Use it in full during the 7-day trial of the Professional plan. Paid plans give access to the module packs. TensorNode is a calculation aid. Every result must be checked and accepted by a qualified engineer, who remains responsible for the design. Read the scope and limits of this module before you rely on a result.

Related modules

  • Beam-Column
    Steel member under combined axial compression and bending to AS 4100 §8
  • Compression Strut
    Axially-loaded steel member (strut / column) to AS 4100
  • Crane Beam
    Overhead-crane runway beam
  • Floor Beam
    Simply-supported steel floor beam to AS 4100
  • Load Stiffener
    Load-bearing web stiffener to AS 4100 §5.14
  • Mullion
    Steel wall mullion / wind post to AS 4100
  • PFC & Plate
    Built-up beam from a PFC (parallel-flange channel) with a welded plate
  • Portal Frame
    Single-bay portal frame to AS 4100

All steel design modules

Open Composite Member with a free account

7 days of the Professional plan, no card. After the trial the account moves to the Free plan; nothing is charged automatically.